MasterFormat: 95

Download this Commercial Laundry Equipment Specification for   WORD | WP | RTF | TEXT

Find over 500 more construction specifications | Arcat.com

	SECTION 11110
	COMMERCIAL LAUNDRY EQUIPMENT
	** NOTE TO SPECIFIER ** Continental Girbau, Inc; Commercial Industrial Laundry Equipment. . This section is based on the products of Continental Girbau, which is located at: 2500 State Road 44. Oshkosh, WI 54904. Toll Free Te1: (800)256-1073. Tel: (920) 231-8222. Fax: (920)231-4666. Email: info@continentalgirbau.com. Web: www.continentalgirbau.com. . Continental Girbau was established in 1995 as the North American subsidiary of the 80-year-old, laundry-equipment manufacturer, Girbau S.A., headquartered in Vic, Spain. Family owned, Girbau employs more than 637 people throughout its corporate headquarters in Vic and subsidiaries in France, United Kingdom, Brazil, Argentina, Germany, United Arab Emirates, China, India and the United States. It markets its commercial and industrial laundry products to more than 80 countries worldwide.
	PART 1	GENERAL
	1.1	SECTION INCLUDES
	** NOTE TO SPECIFIER ** Delete items below not required for project.
		A.	Washer - Extractors.
		B.	Drying Tumblers.
		C.	Flatwork Ironers.
	1.2	RELATED SECTIONS
	** NOTE TO SPECIFIER ** Delete any sections below not relevant to this project; add others as required.
		A.	Section 15105 - Pipes and Tubes: Water Supply piping.
		B.	Section 15150 - Sanitary Waste and Vent Piping: Waste piping.
		C.	Section 15190 - Fuel Piping: Natural or LP gas supply lines and fittings.
		D.	Section 15460 - Domestic Water Conditioning Equipment: Water softeners.
		E.	Section 15800 - Air Distribution: Hot air exhaust outlets.
		F.	Section 16100 - Wiring Methods: Electrical power connections.
	1.3	SUBMITTALS
		A.	Submit under provisions of Section 01300.
		B.	Product Data: Manufacturer's data sheets on each product to be used, including:
			1.	Preparation instructions and recommendations.
			2.	Storage and handling requirements and recommendations.
			3.	Installation methods.
		C.	Shop Drawings: Provide drawings depicting the plan and elevation views of each model specified, with notations for supply and waste line connections, chemical connections, steam supply, electrical connections, handing and any other pertinent placement information. Coordinate with locations found on the Contract Drawings.
	** NOTE TO SPECIFIER ** Delete selection samples if colors have already been selected.
		D.	Selection Samples: For each finish product specified, two complete sets of samples representing manufacturer's full range of available colors and patterns.
		E.	Verification Samples: For each finish product specified, two samples that depict the actual product, color, and pattern.
	1.4	QUALITY ASSURANCE
		A.	Manufacturer Qualifications: All primary products specified in this section will be supplied by a single manufacturer with a minimum of ten (10) years experience.
		B.	Installer Qualifications: All products listed in this section are to be installed by a single installer with a minimum of five (5) years demonstrated experience in installing products of the same type and scope as specified.
		C.	Certifications:
	** NOTE TO SPECIFIER ** Retain only certifications applicable to products specified in this section and delete all others.
			1.	Washer-Extractors: Listed with CSA or ETL, ISO 9001 & 14001 Quality and Environmental Impact Standards.
			2.	Top load Washers: UL or CSA Listed
			3.	Dryers: UL or CSA Listed.
			4.	Ironers: Listed with CSA or ETL, ISO 9001 & 14001 Quality and Environmental Impact Standards.
	1.5	DELIVERY, STORAGE, AND HANDLING
		A.	Store products in manufacturer's unopened packaging until ready for installation.
		B.	Store and dispose of hazardous materials, and materials contaminated by hazardous materials, in accordance with requirements of local authorities having jurisdiction.
	1.6	PROJECT CONDITIONS
		A.	Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's absolute limits.
	1.7	WARRANTY
		A.	At project closeout, provide to Owner or Owners Representative an executed copy of the manufacturer's standard limited warranty against manufacturing defect, outlining its terms, conditions, and exclusions from coverage.
	** NOTE TO SPECIFIER ** Retain only warranty information for products specified in this section. Delete all products not required.
			1.	Washer-Extractors
				a.	Parts: Three (3) years on all machine parts from date of installation or three and one half (3 1/2) years from date of manufacture; which ever comes first.
				b.	Washer Mainframe, inner cylinder, including shaft and coupler, bearings and seals: Five (5) years from the date of installation or five and one half (5 1/2) years from the date of manufacture; which ever comes first.
			2.	Topload Washers: Three (3) Years on all machine parts from date of installation. Dryers: Three (3) Years on all machine parts from the date of installation.
			3.	Ironers:
				a.	Mainframe and Rolls: Five (5) years on parts.
				b.	Machine components (excluding ribbons): Three (3) years on parts from date of installation or three and one half (3 1/2) years from date of manufacture.
	PART 2	PRODUCTS
	2.1	MANUFACTURERS
		A.	Acceptable Manufacturer: Continental Girbau, Inc., which is located at: 2500 State Rd. 44 ; Oshkosh, WI 54904; Toll Free Tel: 800-256-1073; Tel: 920-231-8222 ; Email: request info; Web: www.continentalgirbau.com
	** NOTE TO SPECIFIER ** Delete one of the following two paragraphs; coordinate with requirements of Division 1 section on product options and substitutions.
		B.	Substitutions: Not permitted.
		C.	Requests for substitutions will be considered in accordance with provisions of Section 01600.
	** NOTE TO SPECIFIER ** Retain only models required and delete all others. Delete the entire next article if Pro Series Washers are not specified.
	2.2	PRO-SERIES WASHER- EXTRACTORS
		A.	Pro-Series Washer-Extractor - General Characteristics:
			1.	Cylinder (inner/outer) module front face and door frame material: AISI Type 304. Cabinet (Top/Lower Front/ Pillars/Sides) material: Titan coated steel.
			2.	Cycle Selection: Unit provides a minimum of 79 laundry cycles with a minimum of 59 cycles that may be customized to adapt to specific linen processing requirements.
			3.	Programmable Controls:
				a.	Equipped with a microprocessor control allowing adjustment of wash/rinse temperatures, water level up to a minimum of six (6) levels, three (3) pre-programmed rotation options plus "0" rotation and the ability to program any on/off rotation combination.
				b.	Allows programming of up to ninety-nine (99) minutes per phase, delay start control, display cycle progress through LED indicator located on control panel and shall allow management to limit operator programming through the use of a program access key and cycle lockout function.
			4.	Water Temperature Control/Progressive Cool Down: Operator controlled pre-set wash temperatures from 33 degrees F to 194 degrees F (0.5 degrees C - 90 degrees C) to adapt to specific linen treatment specifications and/or government sanitary regulations. Water inlet valve shall be thermostatically controlled. Steam or Electric auxiliary heat units shall be available to field retrofit at the user option at anytime. Unit shall be capable of a gradual reduction of water temperature from wash to rinse so to reduce fabric shock/wrinkles. Reduction shall be limited to no more than 7 degrees F (14 degrees C) per minute until 113 degrees F (45 degrees C) is reached.
			5.	Noise & In-Line Filters:
				a.	No more than 70 dB (Measured Equivalent Continuous) at the workstation of the unit.
				b.	Standard in-line circuit filters that reduce induced noise and radiating noise for output wiring.
				c.	Standard in-line DC reactor for improving the input power-factor and reducing harmonics when the voltage imbalance exceeds 2 percent.
	** NOTE TO SPECIFIER ** Delete the next paragraph if Water Re-Use System is not specified.
			6.	Water Re-Use System: All control function, and ability to allow a field added water reclamation system capable of reclaiming rinse water for use in subsequent wash, pre-wash and initial rinse phases - select models only.
			7.	Automatic Chemical Injection/Chemical Dispenser: Five (5) independent chemical injection connections for automatic dispensing of liquid chemicals with a minimum of five (5) independent activation signals. For safety purposes all connection ports shall be mounted on the rear of the machine. Unit equipped with a top mounted four(4)- compartment pre-wash and wash detergent/bleach/softener dispenser.
			8.	Program Accelerator/ Visual Cycle Indicator: Operator may manually accelerate program to permit bypass of any program step. Accelerator control and visual cycle indicator located on the microprocessor control and shall allow operator to monitor cycle progress/position.
			9.	Bearing Housing: Solid, one (1) piece construction for optimum structural support with moisture weep bearing protection system.
			10.	Suspension System: Internal suspension system capable of absorbing up to 95 percent of transmitted load dynamic energy (vibration) and isolating it away from electrical components, major mechanical components (bearings, shaft, frame) and the floor. Unit shall be freestanding and not require bolt down or pin attachment to floor structure and should require no additional foundation from standard commercial construction for mounting.
		B.	Model - H2055:
			1.	Capacity:
				a.	Weight: 55 lbs (23 kg).
				b.	Volume: 8.2 cu ft (228 cu dm).
			2.	Size / Dimensions:
				a.	Cylinder Diameter: 29.1 inches (740 mm).
				b.	Cylinder Depth: 21 inches (530 mm).
				c.	Height: 55.9 inches (1420 mm).
				d.	Depth: 47.2 inches (1200 mm).
				e.	Width: 39.4 inches (1000 mm).
				f.	Floor to Door Height: 26.2 inches (665 mm).
				g.	Door Opening: 15.75 inches (400 mm).
			3.	Dynamic Load: Dynamic load to floor shall not exceed 265-pounds with a frequency of 16 Hz.
	** NOTE TO SPECIFIER ** Auxiliary Heating is optional. Delete one of the next two paragraphs if auxiliary heat is specified or both paragraphs if auxiliary heating is not specified.
			4.	Auxiliary Heating: Electric.
				a.	Auxiliary Heating Element: 20.8 kVA.
			5.	Auxiliary Heating: Steam.
				a.	Steam Pressure: 29 to 87 psi (2-6 bar).
				b.	Steam Flow: 176 lbs/ hr (80 kg/hr).
			6.	Mechanical:
				a.	Drain: 3 inches (76 mm).
				b.	Inlets: 3/4 inch (19 mm).
				c.	Water Pressure: 7 to 87 psi (0.5 - 6 bar).
				d.	Water Flow Rate: 16 gal / min (60 l/min).
				e.	Steam Connection: 1/2 inch (13 mm).
				f.	Motor Power: 1.8 kVA.
	** NOTE TO SPECIFIER ** Select power source. Delete two of the next three paragraphs.
			7.	Power/Performance: 208-240V/60Hz/Single Phase.
				a.	Washing Speeds: 14/25/35/46 RPM.
				b.	Spin Speeds: 83/400/530/660Hz/800 RPM.
				c.	G-Force: 2.8/66/116/180/265.
			8.	Power/Performance: 208-240V/60Hz/Three Phase.
				a.	Washing Speeds: 14/25/35/46 RPM.
				b.	Spin Speeds: 83/400/600/800/917 RPM.
				c.	G-Force: 2.8/66/149/264/380.
			9.	Power/Performance: 440-480V/60Hz/Three Phase.
				a.	Washing Speeds: 14/25/35/46 RPM.
				b.	Spin Speeds: 83/400/600/800/917 RPM.
				c.	G-Force: 2.8/66/149/264/380.
		C.	Model - H2090:
			1.	Capacity:
				a.	Weight: 90 lbs (40 kg).
				b.	Volume: 14.1 cu ft (400 cu dm).
			2.	Size / Dimensions:
				a.	Cylinder Diameter: 35.5 inches (902 mm).
				b.	Cylinder Depth: 24.75 inches (628 mm).
				c.	Height: 66.9 inches (1700 mm).
				d.	Depth: 55.4 inches (1407 mm).
				e.	Width: 53.9 inches (1370 mm).
				f.	Floor to Door Height: 29.9 inches (760 mm).
				g.	Door Opening: 22 inches (559 mm).
			3.	Dynamic Load: Dynamic load to floor shall not exceed 536-pounds with a frequency of 14.5 Hz.
	** NOTE TO SPECIFIER ** Auxiliary Heating is optional. Delete one of the next two paragraphs if auxiliary heat is specified or both paragraphs if auxiliary heating is not specified.
			4.	Auxiliary Heating: Electric.
				a.	Heating Element: 25.7 kVA.
			5.	Auxiliary Heating: Steam.
				a.	Steam Pressure: 29 to 87 psi (2-6 bar).
				b.	Steam Flow: 397 lbs/ hr (180 kg/hr).
			6.	Performance:
				a.	Washing Speeds: 15/24/33/41 RPM.
				b.	Spin Speeds: 68/431/575/725/870 RPM.
				c.	G-Force: 2.3/93/166/264/380.
			7.	Mechanical:
				a.	Drain: 3 inches (76 mm).
				b.	Inlets: 1 inch (25.4 mm).
				c.	Water Pressure: 7 to 87 psi (0.5 - 6 bar).
				d.	Water Flow Rate: 26 gal / min (100 l/min).
				e.	Steam Connection: 3/4 inch (19 mm).
				f.	Motor Power: 4.8 kVA.
	** NOTE TO SPECIFIER ** Select power source. Delete one of the next two paragraphs.
				g.	Power: 208-240V/60Hz/Three Phase.
				h.	Power: 440-480V/60Hz/Three Phase.
		D.	Model - H2130 Stationary:
			1.	Capacity:
				a.	Weight: 130 lbs (59 kg).
				b.	Volume: 20.1 cu ft (569 cu dm).
			2.	Size / Dimensions:
				a.	Cylinder Diameter: 42.5 inches (1080 mm).
				b.	Cylinder Depth: 24.4 inches (621 mm).
				c.	Height: 74.8 inches (1900 mm).
				d.	Depth: 57.1 inches (1450 mm).
				e.	Width: 61 inches (1550 mm).
				f.	Floor to Door Height: 35.7 inches (908 mm).
				g.	Door Opening: 22 inches (559 mm).
			3.	Dynamic Load: Dynamic load to floor shall not exceed 661-pounds with a frequency of 13.5 Hz.
	** NOTE TO SPECIFIER ** Auxiliary Heating is optional. Delete one of the next two paragraphs if auxiliary heat is specified or both paragraphs if auxiliary heating is not specified.
			4.	Auxiliary Heating: Electric.
				a.	Heating Element: 40 kVA.
			5.	Auxiliary Heating: Steam.
				a.	Steam Pressure: 29 to 87 psi (2-6 bar).
				b.	Steam Flow: 397 lbs/ hr (180 kg/hr).
			6.	Performance:
				a.	Washing Speeds: 10/20/29/38 RPM.
				b.	Spin Speeds: 60.5/400/550Hz/700/800 RPM.
				c.	G-Force: 2.2/97/183/296/387.
			7.	Mechanical:
				a.	Drain: 3 inches (76 mm).
				b.	Inlets: 1 inch (25.4 mm).
				c.	Water Pressure: 7 to 87 psi (0.5 - 6 bar).
				d.	Water Flow Rate: 26 gal/min (100 l/min).
				e.	Steam Connection: 3/4 inch (19 mm).
				f.	Motor Power: 7.3 kVA.
	** NOTE TO SPECIFIER ** Select power source. Delete one of the next two paragraphs.
				g.	Power: 208-240V/60Hz/Three Phase.
				h.	Power: 440-480V/60Hz/Three Phase.
		E.	Model - H2130 Tilt:
			1.	Capacity:
				a.	Weight: 130 lbs (59 kg).
				b.	Volume: 20.1 cu ft (569 cu dm).
			2.	Size / Dimensions:
				a.	Cylinder Diameter: 42.5 inches (1080 mm).
				b.	Cylinder Depth: 24.4 inches (621 mm).
				c.	Height: 82.4 inches (2092 mm).
				d.	Depth: 63.5 inches (1614 mm).
				e.	Width: 64.5 inches (1639 mm).
				f.	Floor to Door Height: 43.3 inches (1100 mm).
				g.	Door Opening: 22 inches (559 mm).
			3.	Dynamic Load: Dynamic load to floor shall not exceed 661-pounds with a frequency of 13.5 Hz.
	** NOTE TO SPECIFIER ** Auxiliary Heating is optional. Delete one of the next two paragraphs if auxiliary heat is specified or both paragraphs if auxiliary heating is not specified.
			4.	Auxiliary Heating: Electric.
				a.	Heating Element: 40 kVA.
			5.	Auxiliary Heating: Steam.
				a.	Steam Pressure: 29 to 87 psi (2-6 bar).
				b.	Steam Flow: 397 lbs/hr (180 kg/hr).
			6.	Performance:
				a.	Washing Speeds: 10/20/29/38 RPM.
				b.	Spin Speeds: 60.5/400/550Hz/700/800 RPM.
				c.	G-Force: 2.2/97/183/296/387.
			7.	Mechanical:
				a.	Drain: 3 inches (76 mm).
				b.	Inlets: 1 inch (25.4 mm).
				c.	Water Pressure: 7 to 87 psi (0.5 - 6 bar).
				d.	Water Flow Rate: 26 gal/min (100 l/min).
				e.	Steam Connection: 3/4 inch (19 mm).
				f.	Compressed Air Connection: 3/8 inch (10 mm).
				g.	Compressed Air Pressure: 98 psi (7 bar).
				h.	Compressed Air Flow: 7.1 cfm (200 l/m).
				i.	Motor Power: 7.3 kVA.
	** NOTE TO SPECIFIER ** Select power source. Delete one of the next two paragraphs.
				j.	Power: 208-240V/60Hz/Three Phase.
				k.	Power: 440-480V/60Hz/Three Phase.
		F.	Model - H2255 Stationary:
			1.	Capacity:
				a.	Weight: 255 lbs (110 kg).
				b.	Volume: 38.9 cu ft (1100 cu dm).
			2.	Size / Dimensions:
				a.	Cylinder Diameter: 51.5 inches (1310 mm).
				b.	Cylinder Depth: 32 inches (816 mm).
				c.	Height: 80.9 inches (2055 mm).
				d.	Depth: 74.8 inches (1900 mm).
				e.	Width: 69.7 inches (1770 mm).
				f.	Floor to Door Height: 35.8 inches (909 mm).
				g.	Door Opening: 27 inches (686 mm).
			3.	Dynamic Load: Dynamic load to floor shall not exceed 1213-pounds with a frequency of 12 Hz.
	** NOTE TO SPECIFIER ** Auxiliary Heating is optional. Delete the next paragraph if auxiliary heating is not specified.
			4.	Auxiliary Heating: Steam.
				a.	Steam Pressure: 29 to 87 psi (2-6 bar).
				b.	Steam Flow: 794 lbs/hr (360 kg/hr).
			5.	Performance:
				a.	Washing Speeds: 10/17/24/32 RPM.
				b.	Spin Speeds: 50Hz/360Hz/480V/610/720 RPM.
				c.	G-Force: 1.8/95/169/273/280.
			6.	Mechanical:
				a.	Drain: 5 inches (127 mm).
				b.	Inlets: 2 inch (51mm).
				c.	Water Pressure: 7 to 87 psi (0.5 - 6 bar).
				d.	Water Flow Rate: 58 gal/min (220 l/min).
				e.	Steam Connection: 1 inch (25.4 mm).
				f.	Motor Power: 11 kVA.
	** NOTE TO SPECIFIER ** Select power source. Delete one of the next two paragraphs.
				g.	Power: 208-240V/60Hz/Three Phase.
				h.	Power: 440-480V/60Hz/Three Phase.
		G.	Model - H2255 Tilt:
			1.	Capacity:
				a.	Weight: 255 lbs (110 kg).
				b.	Volume: 38.9 cu ft (1100 cu dm).
			2.	Size / Dimensions:
				a.	Cylinder Diameter: 51.5 inches (1310 mm).
				b.	Cylinder Depth: 32 inches (816 mm).
				c.	Height: 88.3 inches (2243 mm).
				d.	Depth: 80.6 inches (2048 mm).
				e.	Width: 72 inches (1830 mm).
				f.	Floor to Door Height: 43.2 inches (1097 mm).
				g.	Door Opening: 27 inches (686 mm).
			3.	Dynamic Load: Dynamic load to floor shall not exceed 1213-pounds with a frequency of 12 Hz.
	** NOTE TO SPECIFIER ** Auxiliary Heating is optional. Delete the next paragraph if auxiliary heating is not specified.
			4.	Auxiliary Heating: Steam.
				a.	Steam Pressure (optional): 29 to 87 psi (2-6 bar).
				b.	Steam Flow (optional): 794 lbs/hr (360 kg/hr).
			5.	Performance:
				a.	Washing Speeds: 10/17/24/32 RPM.
				b.	Spin Speeds: 50Hz/360Hz/480V/610/720 RPM.
				c.	G-Force: 1.8/95/169/273/280.
			6.	Mechanical:
				a.	Drain: 5 inches (127 mm).
				b.	Inlets: 2 inch (51 mm).
				c.	Water Pressure: 7 to 87 psi (0.5 - 6 bar).
				d.	Water Flow Rate: 58 gal/min (220 l/min).
				e.	Steam Connection: 1 inch (25.4 mm).
				f.	Compressed Air Connection: 3/8 inch (10 mm).
				g.	Compressed Air Pressure: 98 psi (7 bar).
				h.	Compressed Air Flow: 7.1 cfm (200 l/m).
				i.	Motor Power: 11 kVA.
	** NOTE TO SPECIFIER ** Select power source. Delete one of the next two paragraphs.
				j.	Power: 208-240V/60Hz/Three Phase.
				k.	Power: 440-480V/60Hz/Three Phase.
	** NOTE TO SPECIFIER ** Retain only models required and delete all others. Delete the entire next article if E Series Washers are not specified.
	2.3	E-SERIES WASHER - EXTRACTORS
		A.	E-Series Washer-Extractor General Characteristics:
			1.	Cylinder (inner/outer) module front face material: AISI Type 304. Cabinet (Top/Lower Front/ Pillars/Sides) material: Titan steel finish.
			2.	Noise & In-Line Filters:
				a.	No more than 70 dB (Measured Equivalent Continuous) at the workstation of the unit.
				b.	Standard in-line circuit filters that reduce induced noise and radiating noise for output wiring.
				c.	Standard in-line DC reactor for improving the input power-factor and reducing harmonics when the voltage imbalance exceeds 2 percent.
			3.	Wash Wheel and Lifters:
				a.	Wash wheel polished to a clean finish and free of bolts and visible welds.
				b.	Funneled tub perforations in order to protect wash items damage caused from sharp edges.
				c.	Tub lifter with top and side perforations that lift and drop water and wash items together providing superior load saturation, chemical penetration and improved rinsing.
			4.	Bearing Housing/Protection: Solid one (1) piece construction for optimum structural support and must have an in-line bearing protection weep system allowing any moisture that may breach the seal to be drained away before reaching the main bearing.
			5.	Suspension System: Unit equipped with an internal suspension system capable of absorbing up to 95 percent of transmitted load dynamic energy (vibration) and isolating it away from electrical components, major mechanical components (bearings, shaft, frame) and the floor. Unit shall be freestanding and not require bolt down or pin attachment to floor structure and should require no additional foundation from standard commercial concrete for mounting.
	** NOTE TO SPECIFIER ** Logi Control is optional Delete the next 6 paragraphs if Logi Control is not specified.
		B.	E-Series Washer-Extractor - Logi Control General Characteristics:
			1.	Programmable Extraction: High extract shall be a minimum of 300 G-force with the ability to program any one of six (6) extract speeds.
			2.	Cycle Selection: Maximum of eight (8) laundry cycles to ensure maximum simplicity. Cycles may be customized to adapt to specific linen processing requirements with the ability to program a minimum of two (2) and no more than nine (9) baths (fills) to ensure thorough cleaning and flexibility.
			3.	Programmable Controls:
				a.	Programmable microprocessor control with 8-cycle programs with the ability to program up to nine (9) phases. A phase consists of no less than four (4) programmable fill levels, adjustable fill temperatures in six of nine phases, automatic chemical injection and the ability to program at least three (3) on/off rotation combinations for flush, wash and rinse phases.
				b.	Programming a of up to eight (8) minutes per phase for flush and rinse baths and at least twenty (20) minutes for wash, programmable extract, delay start control, display cycle progress through LED indicator located on control panel and shall allow management to limit operator programming through the use of a secret access code and cycle lockout function.
			4.	Water Temperature Control: Thermostatically controlled water inlet valve. Operator may set pre-set wash temperatures from 32 degrees F to 140 F (0 - 40 degrees C) for designated phases. Wash phase shall allow programmable temperatures from 32 degrees F to 194 degrees F (0 - 90 degrees C) to adapt to specific linen treatment specifications and/or government sanitary regulations.
			5.	Progressive Cool Down: Capable of a gradual reduction of water temperature from wash to rinse so to reduce fabric shock/wrinkles. Reduction shall be no more than 7 degrees F per minute from 194 degrees F to 130 degrees F (90 degrees C - 54 degrees C).
			6.	Automatic Chemical Injection Chemical Dispenser: Eight (8) independent chemical injection connections for automatic dispensing of liquid chemicals with a minimum of four (4) independent activation signals. For safety purposes all connection ports shall be mounted on the rear of the machine. Top mounted four (4) compartment pre-wash and wash detergent / bleach / softener dispenser. The chemistry from liquid supply or hopper compartments must be able to be dispensed automatically at the appropriate time of the cycle only after being diluted with water. The chemical water solution is dispensed to the load below water level to protect the load from possible chemical damage.
	** NOTE TO SPECIFIER ** Inteli Control is optional Delete the next 6 paragraphs if Inteli Control is not specified.
		C.	E-Series Washer-Extractor - Inteli Control General Characteristics:
			1.	Wash / Extraction Speeds: Programmability of at least four (4) wash rotation speeds and at least six (6) levels of extract by phase. High extract is a minimum of 350 G-Force.
			2.	Cycle Selection: At least 20 preprogrammed laundry cycles with the ability to program a minimum of 79 cycles. The programmable cycles shall allow flexibility of as few as one (1) phase / bath or as many as 2Single Phase(s) baths to ensure proper load processing and flexibility.
			3.	Programmable Controls:
				a.	79 fully programmable cycles with the ability to be program manually at the machine or via a card download interface for maximum speed and accuracy for multiple machines or locations.
				b.	Up to 21 Single Phases or bath exchanges. A phase (bath) consists of no less than six (6) programmable fill levels, adjustable fill temperatures, automatic chemical flushing and or injection and the ability to select at least five (5) on/off rotation combinations for flush, wash and rinse phases.
				c.	Display cycle progress through LED indicator using words and Icons located on control panel and shall allow management to limit operator programming through the use of a secret access code and cycle lockout function.
			4.	Water Temperature Control: Thermostatically controlled water inlet valve. Operator may pre-set all phase bath temperatures from 32 degrees F to 194 degrees F (0 - 90 degrees C) to adapt to specific linen treatment specifications and/or government sanitary regulations.
			5.	Progressive Cool Down: Capable of a gradual reduction of water temperature from wash to rinse so to reduce fabric shock/wrinkles. Allows at least four (4) programmable levels of gradient reduction per minute including: 2, 5.5, 9 and 18 degrees F.
			6.	Automatic Chemical Injection Chemical Dispenser: Unit shall provide eight (8) independent chemical injection connections for automatic dispensing of liquid chemicals with a minimum of four (4) independent activation signals with an option for twelve (12). For safety purposes all connection ports shall be mounted on the rear of the machine. Unit shall be equipped with a top mounted four (4)-compartment pre-wash and wash detergent/ bleach/softener dispenser. The chemistry from liquid supply or hopper compartments must be able to be dispensed automatically at the appropriate time of the cycle only after being diluted with water. The control shall allow for the hopper and liquid injection signals to be controlled independently and allow for signal duration/flush programming. The chemical water solution shall be delivered to the load below water level to protect the load from possible chemical damage.
		D.	Model - EH020:
			1.	Capacity:
				a.	Weight: 20 lbs (8 kg).
				b.	Volume: 2.8 cu ft (79.2 cu dm).
			2.	Size / Dimensions:
				a.	Cylinder Diameter: 21.1 inches (536 mm).
				b.	Cylinder Depth: 13.8 inches (351 mm).
				c.	Height: 42.5 inches (1080 mm).
				d.	Width: 27 inches (685 mm).
				e.	Depth: 27.6 inches (700 mm).
				f.	Door Opening: 12.7 inches (322 mm).
				g.	Floor to Door Height: 15.4 inches (390 mm).
			3.	Dynamic Load: Dynamic load to floor shall not exceed 115-pounds with a frequency of 16.2 Hz.
			4.	Performance:
				a.	Washing Speed: 50 RPM.
				b.	Spin Speeds: 50Hz/100/580/690/780/970 RPM.
				c.	G-Force: 0.75/3/101/143/183/300.
			5.	Mechanical:
	** NOTE TO SPECIFIER ** Select Drain size. 1 inch for pump drain, 2 inch for gravity drain. Delete one of the next two paragraphs.
				a.	Drain: 1 inch (25.4 mm) Pump Drain.
				b.	Drain: 2 inches (51 mm) Gravity Drain.
				c.	Inlets: 3/4 inch (19 mm).
				d.	Water Pressure: 30 to 60 psi (2 - 4 bar).
				e.	Water Flow Rate: 8 gal / min (30 l/min).
				f.	Motor Power: 0.8 kW.
				g.	Modified Energy Factor (MEF): 2.21.
				h.	Water Consumption Factor (WCF): 5.03.
			6.	Power: 120V/60Hz/Single Phase.
		E.	Model - EH030:
			1.	Capacity:
				a.	Weight: 30 lbs (13 kg).
				b.	Volume: 4.4 cu ft (126 cu dm).
			2.	Size / Dimensions:
				a.	Cylinder Diameter: 24.4 inches (620 mm).
				b.	Cylinder Depth: 16.4 inches (416 mm).
				c.	Height: 52.2 inches (1325 mm).
				d.	Width: 31.3 inches (796 mm).
				e.	Depth: 34.9 inches (887 mm).
				f.	Door Opening: 12.9 inches (327 mm).
				g.	Floor to Door Height: 20 inches (509 mm).
			3.	Dynamic Load: Dynamic load to floor shall not exceed 201-pounds with a frequency of 16.7 Hz.
			4.	Performance:
				a.	Spin Speeds: 46.5/100/400/600/800/1005 RPM.
				b.	G-Force:.75/3/56/125/222/351.
	** NOTE TO SPECIFIER ** Select Control Type. Delete one of the next two paragraphs.
			5.	Control Type: Logi Control - 46.5 RPM.
			6.	Control Type: Inteli Control - 27/36/43/48 RPM.
			7.	Mechanical:
				a.	Drain: 3 inches (76 mm).
				b.	Inlets: 3/4 inch (19 mm).
				c.	Water Pressure: 30 to 60 psi (2 - 4 bar).
				d.	Water Flow Rate: 16 gal/min (60 l/min).
				e.	Motor Power: 0.87 kW.
				f.	Modified Energy Factor (MEF): 2.08.
				g.	Water Consumption Factor (WCF): 4.68.
			8.	Power: 208-240V/60Hz/Single Phase.
		F.	Model - EH040:
			1.	Capacity:
				a.	Weight: 40 lbs (17.3 kg).
				b.	Volume: 6.1 cu ft (173 cu dm).
			2.	Size / Dimensions:
				a.	Cylinder Diameter: 27.6 inches (700 mm).
				b.	Cylinder Depth: 17.7 inches (450 mm).
				c.	Height: 55.3 inches (1404 mm).
				d.	Width: 34.2 inches (868 mm).
				e.	Depth: 37.9 inches (962 mm).
				f.	Door Opening: 16.8 inches (426 mm).
				g.	Floor to Door Height: 20.3 inches (515 mm).
			3.	Dynamic Load: Dynamic load to floor shall not exceed 212-pounds with a frequency of 15.8 Hz.
			4.	Performance:
				a.	Spin Speeds: 44/100/351/550Hz/750Hz/950 RPM.
				b.	G-Force: 0.75/4/48/119/221/354.
	** NOTE TO SPECIFIER ** Select Control Type. Delete one of the next two paragraphs.
			5.	Control Type: Logi Control - 44 RPM.
			6.	Control Type: Inteli Control - 25/34/40/45.
			7.	Mechanical:
				a.	Drain: 3 inches (76 mm).
				b.	Inlets: 3/4 inch (19 mm).
				c.	Water Pressure: 30 to 60 psi (2 - 4 bar).
				d.	Water Flow Rate: 16 gal/min (60 l/min).
				e.	Motor Power: 1.6 kW.
				f.	Modified Energy Factor (MEF): 1.96.
				g.	Water Consumption Factor (WCF): 5.04.
			8.	Power: 208-240V/60Hz/Single Phase.
	2.4	M-SERIES WASHER - EXTRACTORS
		A.	M-Series Washer-Extractor General Characteristics:
			1.	Cylinder (inner/outer) module front face material: AISI Type 304. Cabinet (Top/Lower Front/ Pillars/Sides) material: Titan steel finish.
			2.	Noise & In-Line Filters:
				a.	No more than 70 dB (Measured Equivalent Continuous) at the workstation of the unit.
				b.	Standard in-line circuit filters that reduce induced noise and radiating noise for output wiring.
				c.	Standard in-line DC reactor for improving the input power-factor and reducing harmonics when the voltage imbalance exceeds 2 percent.
			3.	Wash Wheel and Lifters:
				a.	Wash wheel polished to a clean finish and free of bolts and visible welds.
				b.	Funneled tub perforations in order to protect wash items damage caused from sharp edges.
				c.	Tub lifter with top and side perforations that lift and drop water and wash items together providing superior load saturation, chemical penetration and improved rinsing.
			4.	Bearing Housing/Protection: Solid one (1) piece construction for optimum structural support and must have an in-line bearing protection weep system allowing any moisture that may breach the seal to be drained away before reaching the main bearing.
		B.	M-Series Washer-Extractor - Logi Control General Characteristics
			1.	Programmable Extraction: High extract shall be a minimum of 108 G-force with the ability to program any one of six (6) extract speeds.
			2.	Cycle Selection: Maximum of eight (8) laundry cycles to ensure maximum simplicity. Cycles may be customized to adapt to specific linen processing requirements with the ability to program a minimum of two (2) and no more than nine (9) baths (fills) to ensure thorough cleaning and flexibility.
			3.	Programmable Controls:
				a.	Programmable microprocessor control with 8-cycle programs with the ability to program up to nine (9) phases. A phase consists of no less than four (4) programmable fill levels, adjustable fill temperatures in six of nine phases, automatic chemical injection and the ability to program at least three (3) on/off rotation combinations for flush, wash and rinse phases.
				b.	Programming a of up to eight (8) minutes per phase for flush and rinse baths and at least twenty (20) minutes for wash, programmable extract, delay start control, display cycle progress through LED indicator located on control panel and shall allow management to limit operator programming through the use of a secret access code and cycle lockout function.
			4.	Water Temperature Control: Thermostatically controlled water inlet valve. Operator may set pre-set wash temperatures from 32 degrees F to 140 degrees F (0 degrees - 40 degrees C) for designated phases. Wash phase shall allow programmable temperatures from 32 degrees F to 194 degrees F (0 degrees - 90 degrees C) to adapt to specific linen treatment specifications and/or government sanitary regulations.
			5.	Progressive Cool Down: Capable of a gradual reduction of water temperature from wash to rinse so to reduce fabric shock/wrinkles. Reduction shall be no more than 7 degrees F per minute from 194 degrees F to 130 degrees F (90 degrees C - 54 degrees C).
			6.	Automatic Chemical Injection Chemical Dispenser: Eight (8) independent chemical injection connections for automatic dispensing of liquid chemicals with a minimum of four (4) independent activation signals. For safety purposes all connection ports shall be mounted on the rear of the machine. Top mounted four (4) compartment pre-wash and wash detergent / bleach / softener dispenser. The chemistry from liquid supply or hopper compartments must be able to be dispensed automatically at the appropriate time of the cycle only after being diluted with water. The chemical water solution is dispensed to the load below water level to protect the load from possible chemical damage.
		C.	Model - EM025:
			1.	Capacity:
				a.	Dry weight: 25 lbs (11 kg).
				b.	Volume: 3.5 cu ft (99 cu dm).
			2.	Size / Dimensions:
				a.	Cylinder Diameter: 21.1 inches (536 mm).
				b.	Cylinder Depth: 17.3 inches (439 mm).
				c.	Height: 42.5 inches (1080 mm).
				d.	Width: 27 inches (685 mm).
				e.	Depth: 29.9 inches (760 mm).
				f.	Door Opening: 12.7 inches (322 mm).
				g.	Floor to Door Height: 15.4 inches (390 mm).
			3.	Performance:
				a.	Washing Speed: 50 RPM.
				b.	Spin Speeds: 50Hz/100/300/400/500/600 RPM.
				c.	G-Force: 0.75/3/27/48/75/108.
			4.	Mechanical:
				a.	Drain: 2 inches (51mm).
				b.	Inlets: 3/4 inch (19 mm).
				c.	Water Pressure: 30 to 60 psi (2 - 4 bar).
				d.	Water Flow Rate: 8 gal/min (30 l/min).
				e.	Motor Power: 0.35 kW.
				f.	Modified Energy Factor (MEF): 1.53.
				g.	Water Consumption Factor (WCF): 5.68.
			5.	Power: 120V/60Hz/Single Phase.
		D.	Model - EM040:
			1.	Capacity:
				a.	Dry weight: 40 Lbs (17 Kg).
				b.	Volume: 5.9 Cu. ft. (166 cu dm).
			2.	Size / Dimensions:
				a.	Cylinder Diameter: 24.4 inches (620 mm).
				b.	Cylinder Depth: 21.6 inches (549 mm).
				c.	Height: 52.2 inches (1325 mm).
				d.	Width: 29.5 inches (750 mm).
				e.	Depth: 39.5 inches (1016 mm).
				f.	Door Opening: 12.9 inches (327 mm).
				g.	Floor to Door Height: 19.7 inches (500 mm).
			3.	Performance:
				a.	Washing Speed: 46.5 RPM.
				b.	Spin Speeds: 46.5/100/300/400/500/600 RPM.
				c.	G-Force: 0.75/3/31/56/87/125.
			4.	Mechanical:
				a.	Drain: 3 inches (76 mm).
				b.	Inlets: 3/4 inch (19 mm).
				c.	Water Pressure: 30 to 60 psi (2 - 4 bar).
				d.	Water Flow Rate: 16 gal/min (60 l/min).
				e.	Steam Connection: 1/2 inch (12.7 mm).
				f.	Motor Power: 0.7 kW.
				g.	Modified Energy Factor (MEF): 1.73.
				h.	Water Consumption Factor (WCF): 5.33.
			5.	Power: 208-240V/60Hz/Single Phase.
		E.	Model - EM055:
			1.	Capacity:
				a.	Dry weight: 55 lbs (24 kg).
				b.	Volume: 8 cu ft (226 cu dm).
			2.	Size / Dimensions:
				a.	Cylinder Diameter: 27.6 inches (700 mm).
				b.	Cylinder Depth: 23.1 inches (586 mm).
				c.	Height: 55.3 inches (1404 mm).
				d.	Width: 34.2 inches (868 mm).
				e.	Depth: 43.2 inches (1098 mm).
				f.	Door Opening: 16.8 inches (426 mm).
				g.	Floor to Door Height: 20.3 inches (515 mm).
			3.	Performance:
				a.	Washing Speed: 44 RPM.
				b.	Spin Speeds: 44/100/300/400/500/600 RPM.
				c.	G-Force: 0.75/4/35/63/98/141.
			4.	Mechanical:
				a.	Drain: 3 inches (76 mm).
				b.	Inlets: 3/4 inch (19 mm).
				c.	Water Pressure: 30 to 60 psi (2 - 4 bar).
				d.	Water Flow Rate: 16 gal/min (60 l/min).
				e.	Steam Connection: 1/2 inch (12.7 mm).
				f.	Motor Power: 1.6 kW.
				g.	Modified Energy Factor (MEF): 1.65.
				h.	Water Consumption Factor (WCF): 4.81.
			5.	Power: 208-240V/60Hz/Single Phase.
	** NOTE TO SPECIFIER ** Retain only models required and delete all others. Delete the entire next article if L Series Washers are not specified.
	2.5	L SERIES WASHERS - EXTRACTORS
		A.	L-Series Washer-Extractor - General Characteristics
			1.	Cabinet (front top and sides)/Cylinder (Inner and outer) Material: AISI Type 304.
			2.	Cycle Selection: A minimum of 99 laundry cycles with a minimum of 79 cycles, which may be customized to adapt to specific linen processing requirements.
			3.	Programmable Controls:
				a.	Equipped with a microprocessor control allowing adjustment of wash/rinse temperatures, water level up to a minimum of six (6) levels, three (3) variable rotation options plus "0" rotation with option of reprogramming on/off time by the second, and the programming of extraction times up to twelve (12) minutes per phase.
				b.	Allows programming of chemical injection times by one (1) second intervals. Control shall display cycle progress through LED indicator located on control panel.
				c.	Allows management to limit operator programming through the use of a program access key including audit capability of total and individual cycles run, hours of operation and error code counts.
			4.	Water Temperature Control: Operator may set pre-set wash temperatures from 33 degrees F to 194 degrees F (0.5 - 90 degrees C) to adapt to specific linen treatment specifications and/or government sanitary regulations. Water inlet valve shall be thermostatically controlled.
			5.	Progressive Cool Down/Crease Guard: Capable of a gradual reduction of water temperature from wash to rinse so to reduce fabric shock/wrinkles. Reduction limited to no more than 7 degrees F per minute until 113 degrees F is reached.
			6.	Chemical Dispenser: Top mounted four (4)-compartment pre-wash and wash detergent/bleach/softener dispenser. For safety purposes, dispenser cover is self-closing and manufactured using flexible material for optimum durability and longevity.
			7.	Automatic Chemical Injection: Five (5) independent chemical injection connections for automatic dispensing of liquid chemicals with a minimum of four (4) independent activation signals. For safety purposes all connection ports are mounted on the rear of the machine and shall allow for hook-up without removal of the machine's top or rear panel.
			8.	Cycle Lockout: Lockout of any program or programs from operator use in order to eliminate the frequency of operator error.
			9.	Program Accelerator/Visual Cycle Indicator: Operator may manually accelerate program to permit bypass of any program step. Accelerator control and visual cycle indicator is conveniently located on the microprocessor control and allows operator to monitor cycle progress/position. Manual accelerate may be locked out at any time.
			10.	Water Seals: Machine bearings protected by double seals. Main seal composed of EPDM Nitrile rubber for maximum moisture protection.
		B.	Model - L1075:
			1.	Capacity:
				a.	Weight: 75 lbs (32 kg).
				b.	Volume: 11.2 cu ft (318 cu dm).
			2.	Size / Dimensions:
				a.	Cylinder Diameter: 35.5 inches (900 mm).
				b.	Cylinder Depth: 20 inches (500 mm).
				c.	Height: 57 inches (1440 mm).
				d.	Depth: 46 inches (1163 mm).
				e.	Width: 43 inches (1093 mm).
				f.	Floor to Door Height: 16.5 inches (420 mm).
			3.	Performance:
				a.	Washing Speed: 40 RPM.
				b.	Spin Speed: 510 RPM.
				c.	G-Force: 131.
			4.	Mechanical:
				a.	Drain: 3 inches (76 mm).
				b.	Inlets: 3/4 inch (19 mm).
				c.	Water Pressure: 7 to 90 psi (0.5 - 6 bar).
				d.	Water Flow Rate: 16 gal/min (60 l/min).
				e.	Steam Connection: 1/2 inch (12.7 mm).
				f.	Motor Power: 2.7 kW.
	** NOTE TO SPECIFIER ** Select power source. Delete one of the next two paragraphs.
				g.	Power: 208-240V/60Hz/Three Phase.
				h.	Power: 440-480V/60Hz/Three Phase.
	** NOTE TO SPECIFIER ** Auxiliary Heating is optional. Delete one of the next two paragraphs if auxiliary heat is specified or both paragraphs if auxiliary heating is not specified.
			5.	Auxiliary Heating: Electric.
				a.	Heating Element: 21.7 kW.
			6.	Auxiliary Heating: Steam.
				a.	Steam Pressure: 30 to 90 psi (2-6 bar).
				b.	Steam Flow: 220 lbs/ hr (100 kg/hr).
		C.	Model - L1125:
			1.	Capacity:
				a.	Weight: 125 lbs (55 kg).
				b.	Volume: 19.4 cu ft (550 cu dm).
			2.	Size / Dimensions:
				a.	Cylinder Diameter: 42.5 inches (1080 mm).
				b.	Cylinder Depth: 23.5 inches (600 mm).
				c.	Height: 69 inches (1745 mm).
				d.	Depth: 55 inches (1400 mm).
				e.	Width: 56 inches (1422 mm).
				f.	Floor to Door Height: 24.4 inches plus base (620 mm plus base).
			3.	Performance:
				a.	Washing Speed: 34 RPM.
				b.	Spin Speed: 465 RPM.
				c.	G-Force: 130.
			4.	Mechanical:
				a.	Drain: 3 inches (76 mm).
				b.	Inlets: 1 inch (25.4 mm).
				c.	Water Pressure: 7 to 90 psi (0.5 - 6 bar).
				d.	Water Flow Rate: 27 gal/min (100 l/min).
				e.	Steam Connection: 3/4 inch (19 mm).
				f.	Motor Power: 3.5 kW.
	** NOTE TO SPECIFIER ** Select power source. Delete one of the next two paragraphs.
				g.	Power: 208-240V/60Hz/Three Phase.
				h.	Power: 440-480V/60Hz/Three Phase.
	** NOTE TO SPECIFIER ** Auxiliary Heating is optional. Delete one of the next two paragraphs if auxiliary heat is specified or both paragraphs if auxiliary heating is not specified.
			5.	Auxiliary Heating: Electric.
				a.	Heating Element: 34.3 kW.
			6.	Auxiliary Heating: Steam.
				a.	Steam Pressure: 30-90 psi (2-6 bar).
				b.	Steam Flow: 400 lbs/ hr (180 kg/hr).
	** NOTE TO SPECIFIER ** Delete the entire next article if Econ-O-Wash Washers are not specified.
	2.6	ECON-O-WASH WASHERS
		A.	Model - JWT820:
			1.	Capacity: 2.8 cu ft (79 cu dm).
			2.	Size / Dimensions:
				a.	Height: 43 inches (1092 mm).
				b.	Depth: 28 inches (711 mm).
				c.	Width: 25.625 inches (651 mm).
				d.	Floor to Work Surface: 36 inches (914 mm).
				e.	Color: White.
			3.	Performance:
				a.	Washing Speed: 44/67 RPM.
				b.	Spin Speed: 710/473 RPM.
			4.	Motor Power: 1/2 HP.
				a.	Power: 120V/60Hz/Single Phase - 15A Protection.
	** NOTE TO SPECIFIER ** Retain only models required and delete all others. Delete the entire next article if Pro Series Dryers are not specified.
	2.7	PRO SERIES II DRYING TUMBLERS
		A.	Pro Series II Drying Tumblers General Characteristics:
	** NOTE TO SPECIFIER ** Retain only if models CG20-30, CG30-40, CG55-65, CG50-60, CG75-85. Delete the next paragraph if Dryers are not specified.
			1.	Cylinder walls and lifter material: galvanized steel. Rear cylinder back plate material: Annealed stainless steel.
	** NOTE TO SPECIFIER ** Retain only if models CG115-25 or CG165-75. Delete the next paragraph if select Dryer models are not specified.
			2.	Cylinder walls, back plate and lifter material: galvanized steel.
	** NOTE TO SPECIFIER ** Retain only if models CG20-30, CG30-40, CG55-65. Delete the next paragraph if Dryers are not specified.
			3.	Axial airflow system introduces heated air from the back of the cylinder and is directed through the load exiting through the front perforations.
			4.	Microprocessor Control system with four time-dry or auto-dry cycles and a no-heat cycle option. AutoDry selection automatically controls heat cycle runtime based on dryness level of individual loads. AutoDry and time dry allows temperature control by degree (Celsius or Fahrenheit) and automatic load cool-down and special Condition cycle.
		B.	Model - CG20-30:
			1.	Capacity: Up to 30 pounds, 7.7 cu ft (0.22 cu m).
			2.	Size / Dimensions:
				a.	Basket Diameter: 26.5 inches (673 mm).
				b.	Basket Depth: 24 inches (610 mm).
	** NOTE TO SPECIFIER ** Select Height based on heat source. Specify 63.875 inches for gas, 72.25 inches for electric and 76.25 inches for steam. Delete two of the next three paragraphs.
				c.	Height: 63.875 inches (1622 mm).
				d.	Height: 72.25 inches (1835 mm) - optional filler plate.
				e.	Height: 76.25 inches (1937 mm) - optional filler plate.
				f.	Depth: 40.875 inches (1038 mm).
				g.	Width: 28 inches (711 mm).
				h.	Door Opening: 22.68 inches (576 mm).
				i.	Floor to Door: 27.5 inches (699 mm).
			3.	Exhaust Diameter: 6 inches (152 mm).
			4.	Basket Motor: (2) 1/4 HP (19 kW).
	** NOTE TO SPECIFIER ** Select mechanical specifications based on heat source. Delete two of the next three paragraphs. Modify the included text as instructed.
			5.	Mechanical - Gas Heat Source:
	** NOTE TO SPECIFIER ** Select Power Requirements. Delete four of the next five paragraphs.
				a.	Power: 120V/60Hz/Single Phase.
				b.	Power: 208-240V/60Hz/Single Phase.
				c.	Power: 200-208,240V/60Hz/Three Phase.
				d.	Power: 380V/60Hz/Three Phase.
				e.	Power: 460-480V/60Hz/Three Phase.
				f.	Heating: 64,000 BTU/h.
				g.	Inlet Diameter: 1/2 inch (13 mm) Male NPT.
			6.	Mechanical - 12 kW Electric Heat Source:
				a.	Oven Size: 40,956 BTU/h.
	** NOTE TO SPECIFIER ** Select power source. Delete five of the next six paragraphs.
				b.	Power: 208V/60Hz/Single Phase - 64A.
				c.	Power: 240V/60Hz/Single Phase - 57A.
				d.	Power: 200-208V/60Hz/Three Phase - 37A.
				e.	Power: 240V/60Hz/Three Phase - 33A.
				f.	Power: 380V/60Hz/Three Phase - 20A.
				g.	Power: 460-480V/60Hz/Three Phase - 16A.
			7.	Mechanical - Steam Heat Source:
	** NOTE TO SPECIFIER ** Select Power Requirements. Delete four of the next five paragraphs.
				a.	Power: 120V/60Hz/Single Phase.
				b.	Power: 208-240V/60Hz/Single Phase.
				c.	Power: 200-208,240V/60Hz/Three Phase.
				d.	Power: 380V/60Hz/Three Phase.
				e.	Power: 460-480V/60Hz/Three Phase.
				f.	Steam Heating:
					1)	At 100 psi: 134,700 BTU/h.
					2)	At 15 psi: 89,940 BTU/h.
				g.	Steam Inlet: 3/4 inch (19 mm) NPT.
				h.	BHP Consumption:
					1)	At 100 psi: 3.9 BHP.
					2)	At 15 psi: 2.6 BHP.
		C.	Model - CG30-40:
			1.	Capacity: Up to 40 pounds, 12.3 cu ft (0.35 cu m).
			2.	Size / Dimensions:
				a.	Basket Diameter: 30 inches (762 mm).
				b.	Basket Depth: 30 inches (762 mm).
	** NOTE TO SPECIFIER ** Select Height based on heat source. Specify 63.875 inches for gas, 72.25 inches for electric and 76.25 inches for steam. Delete two of the next three paragraphs.
				c.	Height: 63.875 inches (1622 mm).
				d.	Height: 72.25 inches (1835 mm) - optional filler plate.
				e.	Height: 76.25 inches (1937 mm) - optional filler plate.
				f.	Depth: 46.875 inches (1191 mm).
				g.	Width: 31.5 inches (800 mm).
				h.	Door Opening: 22.68 inches (576 mm).
				i.	Floor to Door: 27.5 inches (699 mm).
			3.	Exhaust Diameter: 8 inches (203 mm).
			4.	Basket Motor: (2) 1/4 HP (0.19 kW).
	** NOTE TO SPECIFIER ** Select mechanical specifications based on heat source. Delete three of the next four paragraphs. Modify the included text as instructed.
			5.	Mechanical - Gas Heat Source:
	** NOTE TO SPECIFIER ** Select Power Requirements. Delete four of the next five paragraphs.
				a.	Power: 120V/60Hz/Single Phase.
				b.	Power: 208-240V/60Hz/Single Phase.
				c.	Power: 200-208,240V/60Hz/Three Phase.
				d.	Power: 380V/60Hz/Three Phase.
				e.	Power: 460-480V/60Hz/Three Phase.
				f.	Heating: 90,000 BTU/h.
				g.	Inlet Diameter: 1/2 inch (13mm) Male NPT.
			6.	Mechanical - 24 kW Electric Heat Source:
				a.	Oven Size: 81,912 BTU/h.
	** NOTE TO SPECIFIER ** Select power source. Delete five of the next six paragraphs.
				b.	Power: 208V/60Hz/Single Phase - 64A.
				c.	Power: 240V/60Hz/Single Phase - 57A.
				d.	Power: 200-208V/60Hz/Three Phase - 37A.
				e.	Power: 240V/60Hz/Three Phase - 33A.
				f.	Power: 380V/60Hz/Three Phase - 20A.
				g.	Power: 460-480V/60Hz/Three Phase - 16A.
			7.	Mechanical - Steam Heat Source:
	** NOTE TO SPECIFIER ** Select Power Requirements. Delete four of the next five paragraphs.
				a.	Power: 120V/60Hz/Single Phase.
				b.	Power: 208-240V/60Hz/Single Phase.
				c.	Power: 200-208,240V/60Hz/Three Phase.
				d.	Power: 380V/60Hz/Three Phase.
				e.	Power: 460-480V/60Hz/Three Phase.
				f.	Steam Heating:
					1)	At 100 psi: 166,000 BTU/h.
					2)	At 15 psi: 129,000 BTU/h.
				g.	Steam Inlet: 3/4 inch (19 mm) NPT.
				h.	BHP Consumption:
					1)	At 100 psi: 4.8 BHP.
					2)	At 15 psi: 3.7 BHP.
		D.	Model - CG55-65:
			1.	Capacity: Up to 65 pounds, 17.3 cu ft (0.49 cu m).
			2.	Size / Dimensions:
				a.	Basket Diameter: 33 inches (838 mm).
				b.	Basket Depth: 35 inches (889 mm).
	** NOTE TO SPECIFIER ** Select Height based on heat source. Specify 66.72 inches for gas or 72.25 inches for electric. Delete one of the next two paragraphs.
				c.	Height: 66.72 inches (1695 mm).
				d.	Height: 72.25 inches (1835 mm) with optional filler plate.
				e.	Depth: 53.62 inches (1365 mm).
				f.	Width: 34.5 inches (876 mm).
				g.	Door Opening: 26.89 inches (683 mm).
				h.	Floor to Door: 26.87 inches (682 mm).
			3.	Exhaust Diameter: 8 inches (203 mm).
			4.	Basket Motor: (2) 1/2 HP (0.37 kW).
	** NOTE TO SPECIFIER ** Select mechanical specifications based on heat source. Delete three of the next four paragraphs. Modify the included text as instructed.
			5.	Mechanical - Gas Heat Source:
	** NOTE TO SPECIFIER ** Select Power Requirements. Delete two of the next three paragraphs.
				a.	Power: 120V/60Hz/Single Phase.
				b.	Power: 208-240V/60Hz/Single Phase.
				c.	Power: 200-208,240V/60Hz/Three Phase.
				d.	Heating: 112,000 BTU/h.
				e.	Inlet Diameter: 1/2 inch (13 mm) Male NPT.
			6.	Mechanical - 27 kW Electric Heat Source:
				a.	Oven Size: 92,151 BTU/h.
	** NOTE TO SPECIFIER ** Select power source. Delete one of the next two paragraphs.
				b.	Power: 208V/60Hz/Single Phase - 129A.
				c.	Power: 240V/60Hz/Single Phase - 115A.
		E.	Model - CG50-60:
			1.	Capacity: Up to 60 pounds, 18.6 cu ft (0.53 cu m).
			2.	Size / Dimensions:
				a.	Basket Diameter: 37 inches (940 mm).
				b.	Basket Depth: 30 inches (762 mm).
	** NOTE TO SPECIFIER ** Select Height based on heat source. Specify 76.625 inches for gas / electric, and 80 inches for steam. Delete one of the next two paragraphs.
				c.	Height: 76.625 inches (1946 mm) - gas / electric models.
				d.	Height: 80 inches (2032 mm) - steam model.
				e.	Depth: 47 inches (1194 mm).
				f.	Width: 38.625 inches (981 mm).
				g.	Door Opening: 26.89 inches (683 mm).
				h.	Floor to Door: 30.75 inches (781 mm).
			3.	Exhaust Diameter: 8 inches (203 mm).
			4.	Basket Motor: 1/2 HP (0.37 kW).
	** NOTE TO SPECIFIER ** Retain the next paragraph only if reversing motors are required.
			5.	Reversing Motor: (2) 1/3 HP (0.25).
	** NOTE TO SPECIFIER ** Select mechanical specifications based on heat source. Delete two of the next three paragraphs. Modify the included text as instructed.
			6.	Mechanical - Gas Heat Source:
	** NOTE TO SPECIFIER ** Select Power Requirements. 120V not available on Reversing Unit. Delete four of the next five paragraphs.
				a.	Power: 120V/60Hz/Single Phase.
				b.	Power: 200-208,240V/60Hz/Single Phase.
				c.	Power: 200-208,240V/60Hz/Three Phase.
				d.	Power: 380V/60Hz/Three Phase.
				e.	Power: 460-480V/60Hz/Three Phase.
				f.	Heating: 120,000 BTU/h.
				g.	Inlet Diameter: 1/2 inch (13 mm) Male NPT.
			7.	Mechanical - 30 kW Electric Heat Source:
				a.	Oven Size: 102,390 BTU/h.
	** NOTE TO SPECIFIER ** Select power source. Delete four of the next five paragraphs.
				b.	Power: 200-208V/60Hz/Three Phase.
				c.	Power: 240V/60Hz/Three Phase.
				d.	Power: 380V/60Hz/Three Phase.
				e.	Power: 440V/60Hz/Three Phase.
				f.	Power: 460-480V/60Hz/Three Phase.
			8.	Mechanical - Steam Heat Source:
	** NOTE TO SPECIFIER ** Select Power Requirements. 120V not available on Reversing Unit. Delete five of the next six paragraphs.
				a.	Power: 120V/60Hz/Single Phase.
				b.	Power: 200-208,240V/60Hz/Single Phase.
				c.	Power: 200-208,240V/60Hz/Three Phase.
				d.	Power: 380V/60Hz/Three Phase.
				e.	Power: 440V/60Hz/Three Phase.
				f.	Power: 460-480V/60Hz/Three Phase.
				g.	Steam Heating:
					1)	At 100 psi: 177,500 BTU/h.
					2)	At 15 psi: 119,000 BTU/h.
				h.	Steam Inlet: 3/4 inch (19 mm) NPT.
				i.	BHP Consumption:
					1)	At 100 psi: 5.1 BHP.
					2)	At 15 psi: 3.4 BHP.
		F.	Model - CG75-85:
			1.	Capacity: Up to 85 pounds, 22.4 cu ft (0.634 cu m).
			2.	Size / Dimensions:.
				a.	Basket Diameter: 37 inches (940 mm).
				b.	Basket Depth: 36 inches (914 mm).
	** NOTE TO SPECIFIER ** Select Height based on heat source. Specify 76.625 inches for gas / electric, and 80 inches for steam. Delete one of the next two paragraphs.
				c.	Height: 76.625 inches (1946 mm) - gas / electric models.
				d.	Height: 80 inches (2032 mm) - steam model.
				e.	Depth: 53 inches (1346 mm).
				f.	Width: 38.625 inches (981 mm).
				g.	Door Opening: 26.89 inches (683 mm).
				h.	Floor to Door: 30.75 inches (781 mm).
			3.	Exhaust Diameter: 8 inches (203 mm).
			4.	Basket Motor: 3/4 HP (0.56 kW).
	** NOTE TO SPECIFIER ** Retain the next paragraph only if reversing motors are required.
			5.	Reversing Motor: (2) 1/3 HP (0.25 kW).
	** NOTE TO SPECIFIER ** Select mechanical specifications based on heat source. Delete two of the next three paragraphs. Modify the included text as instructed.
			6.	Mechanical - Gas Heat Source:
	** NOTE TO SPECIFIER ** Select Power Requirements. 120V not available on Reversing Unit. Delete four of the next five paragraphs.
				a.	Power: 120V/60Hz/Single Phase.
				b.	Power: 200-208,240V/60Hz/Single Phase.
				c.	Power: 200-208,240V/60Hz/Three Phase.
				d.	Power: 380V/60Hz/Three Phase.
				e.	Power: 460-480V/60Hz/Three Phase.
				f.	Inlet Diameter: 1/2 inch (13 mm) Male NPT.
			7.	Mechanical - 30 kW Electric Heat Source:
				a.	Oven Size: 102,390 BTU/h.
	** NOTE TO SPECIFIER ** Select power source. Delete four of the next five paragraphs.
				b.	Power: 200-208V/60Hz/Three Phase.
				c.	Power: 240V/60Hz/Three Phase.
				d.	Power: 380V/60Hz/Three Phase.
				e.	Power: 440V/60Hz/Three Phase.
				f.	Power: 460-480V/60Hz/Three Phase.
			8.	Mechanical - Steam Heat Source:
	** NOTE TO SPECIFIER ** Select Power Requirements. 120V not available on Reversing Unit. Delete five of the next six paragraphs.
				a.	Power: 120V/60Hz/Single Phase.
				b.	Power: 200-208,240V/60Hz/Single Phase.
				c.	Power: 200-208,240V/60Hz/Three Phase.
				d.	Power: 380V/60Hz/Three Phase.
				e.	Power: 440V/60Hz/Three Phase.
				f.	Power: 460-480V/60Hz/Three Phase.
				g.	Heating: 165,000 BTU/h.
				h.	Steam Heating:
					1)	At 100 psi: 210,000 BTU/h.
					2)	At 15 psi: 141,000 BTU/h.
				i.	Steam Inlet: 3/4 inch (19 mm) NPT.
				j.	BHP Consumption:
					1)	At 100 psi: 6.1 BHP.
					2)	At 15 psi: 4.1 BHP.
		G.	Model - CG115-25:
			1.	Capacity: Up to 125 pounds, 36.1 cu ft (1.02 cu m).
			2.	Size / Dimensions:
				a.	Basket Diameter: 44 inches (1118 mm).
				b.	Basket Depth: 41 inches (1041mm).
	** NOTE TO SPECIFIER ** Select Height based on heat source. Specify 85.7 inches for gas and 83.5 for steam. Delete one of the next two paragraphs.
				c.	Height: 85.7 inches (2177 mm) - gas model.
				d.	Height: 83.5 inches (2121 mm) - steam model.
				e.	Depth: 67.92 inches (1725 mm).
				f.	Width: 46.38 inches (1178 mm).
				g.	Door Opening: 26.89 inches (683 mm).
				h.	Floor to Door: 31.88 inches (797 mm).
			3.	Exhaust Diameter: 10 inches (254 mm).
			4.	Reversing Motor: 3/4 HP (0.56 kW).
			5.	Motor (Fan): 1 HP (0.75 kW).
	** NOTE TO SPECIFIER ** Select mechanical specifications based on heat source. Delete one of the next two paragraphs. Modify the included text as instructed.
			6.	Mechanical - Gas Heat Source:
	** NOTE TO SPECIFIER ** Select Power Requirements. Delete one of the next two paragraphs.
				a.	Power: 200-208,240V/60Hz/Three Phase.
				b.	Power: 460-480V/60Hz/Three Phase.
				c.	Heating: 300,000 BTU/h.
				d.	Inlet Diameter: 3/4 inch (19 mm) Male NPT.
			7.	Mechanical - Steam Heat Source:
	** NOTE TO SPECIFIER ** Select Power Requirements. Delete two of the next three paragraphs.
				a.	Power: 200-208,240V/60Hz/Three Phase.
				b.	Power: 440V/60Hz/Three Phase.
				c.	Power: 460-480V/60Hz/Three Phase.
				d.	Steam Heating:
					1)	At 100 psi: 405,000 BTU/h.
					2)	At 15 psi: 272,000 BTU/h.
				e.	Steam Inlet: 3/4 inch (19 mm) NPT.
				f.	BHP Consumption:
					1)	At 100 psi: 11.7 BHP.
					2)	At 15 psi: 7.9 BHP.
		H.	Model - CG165-75:
			1.	Capacity: Up to 175 pounds, 49.7 cu ft (1.41 cu m).
			2.	Size / Dimensions:
				a.	Basket Diameter: 50.75 inches (1289 mm).
				b.	Basket Depth: 42.5 inches (1080 mm).
				c.	Height: 94 inches (2388 mm).
				d.	Depth: 68.85 inches (1749 mm).
				e.	Width: 53.12 inches (1349 mm).
				f.	Door Opening: 26.89 inches (683 mm).
				g.	Floor to Door: 33.86 inches (860 mm).
			3.	Exhaust Diameter: 12 inches (305 mm).
			4.	Reversing Motor: 3/4 HP (0.56 kW).
			5.	Motor (Fan): 3 HP (2.24 kW).
	** NOTE TO SPECIFIER ** Select mechanical specifications based on heat source. Delete one of the next two paragraphs. Modify the included text as instructed.
			6.	Mechanical - Gas Heat Source:
	** NOTE TO SPECIFIER ** Select Power Requirements. Delete one of the next two paragraphs.
				a.	Power: 200-208,240V/60Hz/Three Phase.
				b.	Power: 460-480V/60Hz/Three Phase.
				c.	Heating: 395,000 BTU/h.
				d.	Inlet Diameter: 1 inch (25.4 mm) Male NPT.
			7.	Mechanical - Steam Heat Source:
	** NOTE TO SPECIFIER ** Select Power Requirements. Delete two of the next three paragraphs.
				a.	Power: 200-208,240V/60Hz/Three Phase.
				b.	Power: 440V/60Hz/Three Phase.
				c.	Power: 460-480V/60Hz/Three Phase.
				d.	Steam Heating:
					1)	At 100 psi: 648,000 BTU/h.
					2)	At 15 psi: 433,000 BTU/h.
				e.	Steam Inlet: 3/4 inch (19 mm) male NPT.
				f.	Steam Outlet: 1 inch (25.4 mm) NPT.
				g.	BHP Consumption:
					1)	At 100 psi: 18.8 BHP.
					2)	At 15 psi: 12.6 BHP.
	** NOTE TO SPECIFIER ** Delete the entire next article if Pro-Series II Stack Drying Tumblers are not specified.
	2.8	PRO-SERIES II STACK DRYING TUMBLERS
		A.	Pro Series II Drying Stack Drying Tumblers General Characteristics
			1.	Cylinder walls and lifter material: galvanized steel. Rear cylinder backplate material: Annealed stainless steel.
			2.	Cylinder walls, back plate and lifter material: galvanized steel.
			3.	Axial airflow system introduces heated air from the back of the cylinder and is directed through the load exiting through the front perforations.
			4.	Microprocessor Control system with four time-dry heat cycles (High, Medium, Low and Delicates ) cycle option. Time dry allows variable time, temperature control by degree (Celsius or Fahrenheit) and automatic load cool-down.
		B.	Model - CG30X2:
			1.	Capacity: 2-Drying pockets each with capacity up to 30 pounds, 10.6 Cu. Ft. (0.3 cu m) per basket.
			2.	Size / Dimensions:
				a.	Basket Diameter: 30 inches (762 mm).
				b.	Basket Depth: 26 inches (660 mm).
				c.	Height: 76.25 inches (1937mm).
				d.	Depth: 42.76 inches (1086 mm).
				e.	Width: 31.5 inches (800 mm).
				f.	Door Opening: 22.68 inches (576 mm).
				g.	Floor to Door (top door): 48 inches (1219 mm).
			3.	Exhaust Diameter: 8 inches (203 mm).
			4.	Basket Motor: (2) 1/4 HP (0.19 kW).
			5.	Mechanical - Gas Heat Source:
	** NOTE TO SPECIFIER ** Select power source. Delete three of the next four paragraphs.
				a.	Power: 120,208-240V/60Hz/Single Phase.
				b.	Power: 200-208,240V/60Hz/Three Phase.
				c.	Power: 380V/60Hz/Three Phase.
				d.	Power: 460-480V/60Hz/Three Phase.
				e.	Heating (per pocket): 73,000 BTU/h.
				f.	Inlet Diameter: 1/2 inch (12.7 mm) Male NPT.
		C.	Model - CG45X2:
			1.	Capacity: 2-Drying pockets each with capacity up to 45 pounds, 14.8 cu ft (0.419 cu m) per basket.
			2.	Size / Dimensions:
				a.	Basket Diameter: 33 inches (838 mm).
				b.	Basket Depth: 30 inches (762 mm).
				c.	Height: 81.25 inches (2064 mm).
				d.	Depth: 48.62 inches (1235 mm).
				e.	Width: 34.5 inches (876 mm).
				f.	Door Opening: 26.89 inches (683 mm).
				g.	Floor to Door (top door): 49 inches (1245 mm).
			3.	Exhaust Diameter: 10 inches (254 mm).
			4.	Basket Motor: (2) 1/2 HP (0.37 kW).
			5.	Mechanical - Gas Heat Source:
	** NOTE TO SPECIFIER ** Select power source. Delete one of the next two paragraphs.
				a.	Power: 208-240V/60Hz/Single Phase.
				b.	Power: 200-208,240V/60Hz/Three Phase.
				c.	Heating (per pocket): 95,000 BTU/h.
				d.	Inlet Diameter: 1/2 inch (12.7 mm) Male NPT.
	** NOTE TO SPECIFIER ** Delete the entire next article if E Series Dryers are not specified.
	2.9	E SERIES DRYING TUMBLER
		A.	E-Series 20-25 Pound High Performance Dryer - General Characteristics
			1.	Dry Weight Capacity: Rated capacity of up to 25 pounds, allowing for varied linen types and maximum drying speed.
			2.	Cabinet: AISI-304 stainless steel top, front and side panels.
			3.	Cylinder Dimension / Volume: Minimum 26 inch (660 mm) diameter for maximum drop and no more than 24 inches (610 mm) deep for ease of unloading. Cylinder cubic volume shall be a minimum of 7.0 cubic feet (0.2 cu m) with a cylinder light.
			4.	Door Material and Diameter:
				a.	Tumbler door: Steel with a tab latch door system and a shock resistant clear window.
				b.	Window: Mounted without the use of gaskets exposed to the tumbler load that may wear. Door diameter must be at least 20 1/2 inches (510 mm) for ease of loading and unloading.
			5.	Airflow / Vent Diameter: Maximum of 220 cfm for fast, efficient drying and proper balance with input heat energy. Exhaust vent to be a maximum of 4 inches (102 mm) in diameter for gas and electric models.
			6.	Heating Source / Input: Axial airflow design allowing for maximum efficiency. Tumbler basket shall be non-perforated.
			7.	Lint Filtration: Permanently fixed "lint filter" type allowing for easy and frequent removal of lint. For purposes of operator safety, it is not required that the front panel be removed for regular lint cleanout. Screen is constructed of durable nylon construction allowing extended life.
			8.	Drive System: Belt drive and dual-roller system for maximum drive efficiency and long life.
			9.	Control and Features: Microprocessor controlled and capable of five (5) cycle selections with the capability to programming cycles, set vend price, retrieve audit information, and operate diagnostic tests and raid advance options. Any cycle can be modified to set cycle time from 1-99 minutes, temperature (100-160 degrees), and cool-down time (0-59 minutes). The micro displays error modes identifying the cause of safety shutdown. Four-digit display, along with a LED (Light Emitting Diode) for status of lights on the keypad and status words for the control.
			10.	Cycle Status Display: Depicts time remaining (drying cycle, cooling cycle, end of cycle).
			11.	Basket Construction: Non-perforated galvanized steel with a stainless steel back plate and molded polypropylene lifters for extended life and maximum resistance to residual laundry chemicals.
			12.	Motor Configuration: Single motor design: blower/fan motor rated at no less than 1/3 HP maximum efficiency.
		B.	Model - KFE:
			1.	Capacity: Volume: 7.0 cu ft (1990 cu dm).
			2.	Size / Dimensions:
				a.	Height: 40.75 inches (1035 mm).
				b.	Depth: 28 inches (711 mm).
				c.	Width: 26.875 inches (683 mm).
				d.	Door Opening: 20.5 inches (521 mm).
			3.	Exhaust: 4 inch (102 mm) diameter / 220 cfm (374 cu m/h) exhaust air flow.
			4.	Basket Motor: 1/3 HP.
			5.	Mechanical - Electric Heat Source:
				a.	Power: 240V/60Hz/Single Phase - 5350 Watts, 30A Protection.
		C.	Model - KFG:
			1.	Capacity: Volume: 7.0 cu ft (1990 cu dm).
			2.	Size / Dimensions:
				a.	Height: 40.75 inches (1035 mm).
				b.	Depth: 28 inches (711 mm).
				c.	Width: 26.875 inches (683 mm).
				d.	Door Opening: 20.5 inches (521 mm).
			3.	Exhaust: 4 inch (102 mm) diameter / 220 cfm (374 cu m/h) exhaust air flow.
			4.	Basket Motor: 1/3 HP.
			5.	Mechanical - Gas Heat Source:
				a.	Power: 120V/60Hz/Single Phase - 15A Protection.
				b.	Heating: 25,000 BTU/h.
				c.	Inlet Diameter: 3/8 inch (10 mm) NPT.
	** NOTE TO SPECIFIER ** Retain only models required and delete all others. Delete the entire next article if Econ-O-Dry Models are not specified.
	2.10	ECON-O-DRY DRYERS
		A.	Model – JDE - Single Load Dryer:
			1.	Capacity: 7.0 cu ft (199 cu dm).
			2.	Size / Dimensions:
				a.	Height: 43 inches (1092 mm).
				b.	Depth: 28 inches (711 mm).
				c.	Width: 26.875 inches (683 mm).
				d.	Door Opening: 24.7 inches (628 mm).
				e.	Color: White.
			3.	Exhaust:
				a.	Diameter: 4 inches (102 mm).
				b.	Flow: 220 cfm (6.23 cu m/min).
			4.	Basket Motor: 1/3 HP.
			5.	Mechanical - Electric Heat Source:
				a.	Power: 240V/60Hz/Single Phase - 5350 Watts, 30A Protection.
		B.	Model – JDG - Single Load Dryer:
			1.	Capacity: 7.0 cu ft (199 cu dm).
			2.	Size / Dimensions:
				a.	Height: 43 inches (1092 mm).
				b.	Depth: 28 inches (711 mm).
				c.	Width: 26.875 inches (683 mm).
				d.	Door Opening: 24.7 inches (628 mm).
				e.	Color: White.
			3.	Exhaust:
				a.	Diameter: 4 inches (102 mm).
				b.	Flow: 220 cfm (6.23 cu m/min).
			4.	Basket Motor: 1/3 HP.
			5.	Mechanical - Gas Heat Source:
				a.	Voltage: 120/60/1 - 15A Protection.
				b.	Heating: 25,000 BTU/h.
				c.	Inlet Diameter: 3/8 inch (10 mm) NPT.
		C.	Model – JSE - Econ-O-Dry Stack Double Load:
			1.	Capacity: 7.0 cu ft (199 cu dm) per basket.
			2.	Size / Dimensions:
				a.	Height: 76.625 inches (1946 mm).
				b.	Depth: 28 inches (711 mm).
				c.	Width: 26.875 inches (683 mm).
				d.	Door Opening: 24.7 inches (628 mm) per basket.
				e.	Color: White.
			3.	Exhaust:
				a.	Diameter: 4 inches (102 mm).
				b.	Flow: 220 cfm (6.23 cu m/min).
			4.	Basket Motor: 1/3 HP per basket.
			5.	Mechanical - Electric Heat Source:
				a.	Power: 240V/60Hz/Single Phase- 5350 Watts, 30 Amp Protection per basket.
		D.	Model – JSG - Econ-O-Dry Stack Double Load:
			1.	Capacity: 7.0 cu ft (199 cu dm) per basket.
			2.	Size / Dimensions:
				a.	Height: 76.625 inches (1946 mm).
				b.	Depth: 28 inches (711 mm).
				c.	Width: 26.875 inches (683 mm).
				d.	Door Opening: 24.7 inches (628 mm) per basket.
				e.	Color: White.
			3.	Exhaust:
				a.	Diameter: 4 inches (102 mm).
				b.	Flow: 220 cfm (6.23 cu m/min).
			4.	Basket Motor: 1/3 HP per basket.
			5.	Mechanical - Gas Heat Source:
				a.	Voltage: 120/60/1 - 15A Protection per basket.
				b.	Heating: 25,000 BTU/h per basket.
				c.	Inlet Diameter: 3/8 inch (10 mm) NPT.
	** NOTE TO SPECIFIER ** Retain only models required and delete all others. Delete the entire next article if Pro-Series Flatwork Ironers are not specified. See next article for Pro-Series F32 Flatwork Ironers.
	2.11	PRO-SERIES FLATWORK IRONERS (Excluding F32)
		A.	Pro-Series Flatwork Ironers - General Characteristics:
			1.	Roll Material: Constructed of polished chrome for maximum corrosion resistance and do not require the use of wax products for proper operation.
			2.	Exhaust: Rear bottom mounted to keep heat and exhaust away from the operator.
			3.	Feed And Pressure Ribbons: One-piece construction made of polyester for maximum longevity. Pressure ribbons shall be made of NOMEX for optimum heat resistance longevity with covered staple seams for quality ironing and quick replacement. Pressure ribbon contact shall be at least 250 degrees of the roll circumference to ensure optimum linen contact and operate at a speed identical to that of the heated cylinder so as to eliminate linen distortion and ensure iron/dry quality.
			4.	Safety Stop Button: Allows the operator to stop all machine function in case of an emergency or operator error.
			5.	Manual Advance Option: Allows the operator to mechanically advance the roll. This helps to prevent linen damage in the case of power loss.
	** NOTE TO SPECIFIER ** Model F08048 general characteristics. Delete the next paragraph if model F08048 is not specified.
			6.	Control: Unit is controlled through an independently mounted control. Control offers manual speed control settings of 3.5, 5, 6.5 and 10 feet per minute and has a two-way safety device mounted over the entire length of ironer input surface.
	** NOTE TO SPECIFIER ** Model F13__ and F20____ general characteristics. Delete the next 3 paragraphs if model F13__ or F20___ is not specified.
			7.	Control: Unit is controlled through an independently mounted microprocessor control. Control offers AutoSpeed setting capable of automatically adjusting the ironing speed to address specific linen types and moisture retention levels. Microprocessor controlled safety checks, temperature control, process and operating alarm function and built-in electronic diagnostic package for quick service checks.
			8.	Automatic Safty Cool Down: Ironer capable of automatically monitoring the reduction of roll temperature following shutdown of the unit. The heated cylinder, feed and pressure ribbons will continue to operate without heat until a safe temperature is achieved so as to reduce wear and tear and prevent scorching of the ribbons. Once safe temperature is reached the unit will automatically shutdown with no further operator attention.
			9.	Lint Filter: Built-in lint filter for optimum airflow and prevention of lint exhaust to the atmosphere, vents and work area.
	** NOTE TO SPECIFIER ** Model F20____ Optional Integrated Primary Folder. Delete the next paragraph if Optional Integrated Primary Folder is not specified.
			10.	Optional Integrated Primary Folder: Ironer allows for user selected option of an integrated folding system that provides 4-measured primary folds with the ability to save up to 9-different linen dimension in the microprocessor. The micro and folding device also provides an auto fold function selection to automatically measure each item and adjust the fold length without operator input.
		B.	Model - F08048:
			1.	Cylinder Diameter: Minimum 8.7 inches (220 mm).
			2.	Useable Cylinder Length: 47.6 inches (1210 mm).
			3.	Ironing Speed: 3.5 to 10 ft/min (1 to 3 m/min).
			4.	Size / Dimensions:
				a.	Height: 42.8 inches (1088 mm).
				b.	Depth: 30.1 inches (765 mm).
				c.	Width: 67.3 inches (1709 mm).
			5.	Exhaust:
				a.	Diameter: 3.5 inches (90 mm).
				b.	Flow: 75 cfm (128 cu m/h).
			6.	Motor: 0.35 HP (0.267 kW).
			7.	Full Load: 21.1 / 20.3A.
			8.	Heater: 7.2/8 kW.
			9.	Evaporation Capability: 21.5 pounds per hour.
	** NOTE TO SPECIFIER ** Select power source. Delete one of the next two paragraphs.
			10.	Power: 208/60/Three Phase.
			11.	Power: 240/60/Three Phase.
	** NOTE TO SPECIFIER ** Insert the last two digits of the model number based on length selected. Insert "61" for 61 inch length, or "76" for 76 inch length.
		C.	Model - F13__:
			1.	Cylinder Diameter: minimum 12.8 inches (325 mm).
	** NOTE TO SPECIFIER ** Select Length. Delete one of the next two paragraphs.
			2.	Useable Cylinder Length: 61 inches (1550 mm).
			3.	Useable Cylinder Length: 76 inches (1940 mm).
			4.	Ironing Speed: 3 to 16 ft/min (1 to 5 m/min).
			5.	Exhaust:
				a.	Diameter: 4.5 inches (114 mm).
				b.	Flow: 347 cfm (590 cu m/h).
			6.	Motor: 0.67 HP.
			7.	Full Load: 3.5A.
	** NOTE TO SPECIFIER ** Select Heater based on length. 15.6 Kw for 61", 19.6 for 76". Delete one of the next two paragraphs or both if gas heat is specified.
			8.	Heater: Electric - 15.6 kW.
			9.	Heater: Electric - 19.6 kW.
	** NOTE TO SPECIFIER ** Select Heater based on length. 75600 BTU for 61”, 95500 for 76”. Delete three of the next four paragraphs or all four if electric heat is specified.
			10.	Heater: Natural Gas - 75,600 BTU/h, Supply 7(+-1) inch wc.
			11.	Heater: Propane Gas - 75,600 BTU/h, Supply 11(+-0.3) inch wc.
			12.	Heater: Natural Gas - 95,500 BTU/h, Supply 7(+-1) inch wc.
			13.	Heater: Propane Gas - 95,500 BTU/h, Supply 11(+-0.3) inch wc.
	** NOTE TO SPECIFIER ** Select Evaporation capability based on length. 33 pounds per hour for 61", 40 pounds per hour 76"". Delete one of the next two paragraphs.
			14.	Evaporation Capability: 33 pounds per hour.
			15.	Evaporation Capability: 40 pounds per hour.
	** NOTE TO SPECIFIER ** Select Size/Dimensions based on width. 81.4 inches for 61", 96.7 for 76"". Delete one of the next two paragraphs.
			16.	Size / Dimensions:
				a.	Height: 51.9 inches (1319 mm).
				b.	Depth: 34.8 inches (885 mm).
				c.	Width: 81.4 inches (2068 mm).
			17.	Size / Dimensions:
				a.	Height: 51.9 inches (1319 mm).
				b.	Depth: 34.8 inches (885 mm).
				c.	Width: 96.7 inches (2456 mm).
	** NOTE TO SPECIFIER ** Select Power based on heater specified. Retain the next paragraph if gas heat is specified.
			18.	Power: 208-240/60/Single phase.
	** NOTE TO SPECIFIER ** Select Power based on heater specified. Retain one of the next two paragraphs if electric heat is required. Delete both if gas is specified.
			19.	Power: 208/60/Three Phase.
			20.	Power: 240/60/Three Phase.
	** NOTE TO SPECIFIER ** Insert the last three digits of the part number based on length selected. Insert "058" for 58.3 inch, "075" for 74.8 inch, "100" for 99.6 inch, "125" for 124.6 inch length.
		D.	Model - F20___:
			1.	Cylinder Diameter: Minimum 20.1 inches (510 mm).
	** NOTE TO SPECIFIER ** Select Length. Delete three of the next four paragraphs.
			2.	Useable Cylinder Length: 58.3 inches (1480 mm).
			3.	Useable Cylinder Length: 74.8 inches (1900 mm).
			4.	Useable Cylinder Length: 99.6 inches (2530 mm).
			5.	Useable Cylinder Length: 124.6 inches (3165 mm).
			6.	Ironing Speed: 3 to 21 ft/min (1 to 6.5 m/min).
			7.	Exhaust:
				a.	Diameter: 5.1 inches (130 mm).
				b.	Flow: 497 cfm (844 cu m/h).
			8.	Motor: 1.48 HP.
			9.	Full Load: 11.3A.
			10.	Size / Dimensions: Height: 55.9 inches (1420 mm).
			11.	Size / Dimensions: Depth: 45.8 inches (1164 mm).
	** NOTE TO SPECIFIER ** Select Size/Dimensions based on width of Gas and Electric models.. 85.4 inches for 58", 102.2 inches for 75"", 127 inches for 100", 152 inches for 125". Delete one of the next two paragraphs.
			12.	Size / Dimensions: Width: 85.4 inches (2170 mm).
			13.	Size / Dimensions: Width: 102.2 inches (2595 mm).
			14.	Size / Dimensions: Width: 127 inches (3225 mm).
			15.	Size / Dimensions: Width: 152 inches (3860 mm).
	** NOTE TO SPECIFIER ** Select Size/Dimensions based on width of Steam models.. 104.9 inches for 75", 154.7 inches for 125 Delete one of the next two paragraphs.
			16.	Size / Dimensions: Width: 104.9 inches (2665 mm).
			17.	Size / Dimensions: Width: 154.7 inches (3930 mm).
	** NOTE TO SPECIFIER ** Select Heater based on length. 28 Kw for 58.3 inch, 35.5 Kw for 74.8 inch, 47 Kw for 99.6 inch or 60 Kw for 124.6 inch length. Delete three of the next four paragraphs or all four if gas or steam heat is specified.
			18.	Heater: Electric - 28 kW.
			19.	Heater: Electric - 35.5 kW.
			20.	Heater: Electric - 47 kW.
			21.	Heater: Electric - 60 kW.
	** NOTE TO SPECIFIER ** Select Heater based on length. 111000 for 58.3 inch, 143000 for 74.8 inch, 186500 for 99.6 inch, 238000 for 124.6 inch length. Delete seven of the next eight paragraphs or all eight if electric or steam heat is specified.
			22.	Heater: Natural Gas - 111,000 BTU/h, Supply 7(+-1) inch wc.
			23.	Heater: Natural Gas - 143,000 BTU/h, Supply 7(+-1) inch wc.
			24.	Heater: Natural Gas - 186,500 BTU/h, Supply 7(+-1) inch wc.
			25.	Heater: Natural Gas - 238,000 BTU/h, Supply 7(+-1) inch wc.
			26.	Heater: Propane Gas - 111,000 BTU/h, Supply 11(+-0.3) inch wc.
			27.	Heater: Propane Gas - 143,000 BTU/h, Supply 11(+-0.3) inch wc.
			28.	Heater: Propane Gas - 186,500 BTU/h, Supply 11(+-0.3) inch wc.
			29.	Heater: Propane Gas - 238,000 BTU/h, Supply 11(+-0.3) inch wc.
	** NOTE TO SPECIFIER ** Select Heater based on length. Steam only available on 075 and 125 models. 166500 for 74.8 inch, 277750 for 124.6 inch length. Delete one of the next two paragraphs or all both if gas or electric heat is specified.
			30.	Heater: Steam - 166,500 BTU/h.
				a.	Consumption: 146 lbs/h (66 kg/h).
				b.	Pressure: 116 psi (8 bar).
				c.	BHP Consumption: 4.97 BHP.
				d.	Steam Inlet: 1 inch (25.4 mm).
				e.	Condensate Outlet: 0.75 inches (19 mm).
				f.	Safety Valve Discharge Diameter: 0.5 inches (12.7 mm).
			31.	Heater: Steam - 277,750 BTU/h.
				a.	Consumption: 243 lbs/h (66 kg/h).
				b.	Pressure: 116 psi (8 bar).
				c.	BHP Consumption: 8.3 BHP.
				d.	Steam Inlet: 1 inch (25.4 mm).
				e.	Condensate Outlet: 0.75 inches (19mm).
				f.	Safety Valve Discharge Diameter: 0.5 inches (12.7 mm).
			32.	Power: 208-240/60/Three Phase.
	** NOTE TO SPECIFIER ** Select Power based on heater specified. Retain one of the next two paragraphs if electric or steam heat is required. Delete both if gas is specified.
			33.	Power: 208/60/Three Phase.
			34.	Power: 240/60/Three Phase.
	** NOTE TO SPECIFIER ** Retain only models required and delete all others. Delete the entire next article if Pro-Series F32 Heated Chest Flatwork Ironers are not specified.
	2.12	PRO-SERIES F32 HEATED CHEST FLATWORK IRONERS
		A.	Pro-Series Heated Chest Flatwork Ironers - General Characteristics:
			1.	Bed Material/ Roll Diameter: Mirror polished finish to.8 micron for maximum corrosion resistance and optimal ironing performance. Minimum of 31.5 inch (800 mm) roll diameter with complete cylinder perforation for maximum suction.
			2.	Exhaust: Shaft mounted fan to keep heat and exhaust away from the operator.
			3.	Control: Unit mounted microprocessor control. Control offers manual speed control and AutoSpeed setting capable of automatically adjusting the ironing speed to address specific linen types and moisture retention levels. Microprocessor also offers pressure adjustment, roll reverse, safety checks, actual and programmed temperature control, process and operating Alarm function and built-in electronic diagnostic package for quick service checks.
			4.	Discharge Options: Allows for user determined discharge options to a raised platform table or to interface with adjustable height of with ancillary folding, cross-folding and stacking devices.
			5.	Automatic Safety Shut-Down: Capability of automatically lifting the pressure roll from the heated bed following shutdown of the unit. Cylinder pad and feed ribbons are removed from direct contact with any heat energy input until the unit is engaged for production, ensuring maximum longevity.
			6.	Canopy and Bed: Full view canopy allowing for inspection on heat isolation and noise reduction. Provide access to inspection and maintenance area (2-3 roll only) for each canopy and roll area via a diamond-plate platform on the unit. Ironing bed allows for at least 180 degrees of contact and is fully insulated to optimize efficiency.
			7.	Drive System: Speed controlled by a variable speed inverter drive system for optimum roll speed control and operate by specific meter (metric) or foot English Standard) per minute increments with real-speed check and varied roll speed programmability.
			8.	Modular Design: Capable of adding or eliminating roll modules from as few as one (1) to as many as three (3) at any time in order to facilitate increases or decreases in volume and space issues.
			9.	Safety: Safety stop button allows the operator to stop all machine function in case of an emergency or operator error. All pressure components must certified following ASME code and not allow start-up until hand guard check has been performed.
	** NOTE TO SPECIFIER ** Insert three digits of the part number based on length selected. Insert "118" for 118.1 inch, "130" for 129.9 inch, "138" for 137.8 inch.
		B.	Model - 1 Roll - F32___BS:
			1.	Cylinder Diameter: 31.5 inches (800 mm).
	** NOTE TO SPECIFIER ** Select Length. Delete two of the next three paragraphs.
			2.	Useable Cylinder Length: 118.1 inches (3000 mm).
			3.	Useable Cylinder Length: 129.9 inches (3300 mm).
			4.	Useable Cylinder Length: 137.8 inches (3500 mm).
			5.	Ironing Speed: 16 to 82 ft/min (5 to 25 m/min)
			6.	Exhaust:
				a.	Diameter: 9.8 inches (250 mm).
				b.	Flow: 636 cfm (1080 cu m/h).
			7.	Drive Motor: 14.75 HP.
			8.	Blower Motor: 1.74 HP.
			9.	Fan Motor: 0.24 HP.
			10.	Compressed Air Flow: 21 gal/min (80 l/hr).
			11.	Compressed Air Diameter: 0.5 inches (12.7 mm).
			12.	Size / Dimensions: Height: 65 inches (1650 mm).
			13.	Size / Dimensions: Depth: 86 inches (2180 mm).
	** NOTE TO SPECIFIER ** Select Size/Dimensions based on width.. 173 inches for 118", 185 inches for 130" and 193 inches for 138". Delete one of the next three paragraphs.
			14.	Size / Dimensions: Width: 173 inches (4400 mm).
			15.	Size / Dimensions: Width: 185 inches (4700 mm).
			16.	Size / Dimensions: Width: 193 inches (4900 mm).
	** NOTE TO SPECIFIER ** Select Full Load. Delete one of the next two paragraphs
			17.	Full Load 208-240/Three Phase: 40.3A.
			18.	Full Load 440-480/Three Phase: 24.2A.
	** NOTE TO SPECIFIER ** Select Heater based on width. 404940 BTU for 118 inch, 444640 BTU for 130 inch and 468460 BTU for 138 inch, Delete two of the next three paragraphs. Delete next five paragraphs if Steam Heater is not specified.
			19.	Heater: Steam - 404,940 BTU.
				a.	Consumption: 353 lbs/h (160 kg/h).
				b.	Pressure: 116 psi (8 bar).
				c.	BHP Consumption: 9.7 BHP.
			20.	Heater: Steam - 444,640 BTU.
				a.	Consumption: 386 lbs/h (175 kg/h).
				b.	Pressure: 116 psi (8 bar).
				c.	BHP Consumption: 10.7 BHP.
			21.	Heater: Steam - 468,460 BTU.
				a.	Consumption: 408 lbs/h (185 kg/h).
				b.	Pressure: 116 psi (8 bar).
				c.	BHP Consumption: 11.2 BHP.
			22.	Steam Inlet Diameter: 1.5 inches (38.1 mm).
			23.	Condensate Outlet Diameter: 1.5 inches (38.1 mm).
	** NOTE TO SPECIFIER ** Select Hot Oil Flow based on width. 106 gal/min for 118 inch, 116 gal/min for 130 inch and 122 gal/min for 138 inch, Delete two of the next three paragraphs. Delete the next four paragraphs if Hot Oil Heater is not specified.
			24.	Hot Oil Flow: 106 gal/min (400 l/hr).
			25.	Hot Oil Flow: 116 gal/min (440 l/hr).
			26.	Hot Oil Flow: 122 gal/min (460 l/hr).
			27.	Hot Oil Pressure: 29 psi (2 bar).
			28.	Hot Oil Inlet Diameter: 3 inches (76.2 mm).
			29.	Hot Oil Outlet Diameter: 3 inches (76.2 mm).
		C.	Model - 2-Roll- F32___CS:
			1.	Cylinder Diameter: 31.5 inches (800mm).
	** NOTE TO SPECIFIER ** Select Length. Delete two of the next three paragraphs.
			2.	Useable Cylinder Length: 118.1 inches (3000 mm).
			3.	Useable Cylinder Length: 129.9 inches (3300 mm).
			4.	Useable Cylinder Length: 137.8 inches (3500 mm).
			5.	Ironing Speed: 16 to 131 ft (5 to 40 m) per minute.
			6.	Exhaust:
				a.	Diameter: 9.8 inches (250 mm).
				b.	Flow: 1271 cfm (2160 cu m/h).
			7.	Drive Motor: 14.75 HP.
			8.	Blower Motor: 2 x 1.74 HP.
			9.	Fan Motor: 0.24 HP.
			10.	Compressed Air Flow: 40 gal/min (150 l/hr).
			11.	Compressed Air Diameter: 0.5 inches (12.7 mm).
			12.	Size / Dimensions: Height: 65 inches (1650 mm).
			13.	Size / Dimensions: Depth: 138 inches (3510 mm).
	** NOTE TO SPECIFIER ** Select Size/Dimensions based on width.. 173 inches for 118", 185 inches for 130" and 193 inches for 138". Delete one of the next three paragraphs.
			14.	Size / Dimensions: Width: 173 inches (4400 mm).
			15.	Size / Dimensions: Width: 185 inches (4700 mm).
			16.	Size / Dimensions: Width: 193 inches (4900 mm).
	** NOTE TO SPECIFIER ** Select Full Load based on power. Delete one of the next two paragraphs
			17.	Full Load 208-240/Three Phase: 44.5A.
			18.	Full Load 440-480/Three Phase: 26.7A.
	** NOTE TO SPECIFIER ** Select Heater based on width. 889280 BTU for 118 inch, 976620 BTU for 130 inch and 1032200 BTU for 138 inch, Delete two of the next three paragraphs. Delete next five paragraphs if Steam Heater is not specified.
			19.	Heater: Steam - 889,280 BTU.
				a.	Consumption: 772 lbs/h (350 kg/h)
				b.	Pressure: 116 psi (8 bar).
				c.	BHP Consumption: 21.3 BHP
			20.	Heater: Steam - 976,620 BTU
				a.	Consumption: 849 lbs/h (385 kg/h).
				b.	Pressure: 116 psi (8 bar).
				c.	BHP Consumption: 23.4 BHP.
			21.	Heater: Steam - 1,032,200 BTU.
				a.	Consumption: 909 lbs/h (410 kg/h).
				b.	Pressure: 116 psi (8 bar).
				c.	BHP Consumption: 24.7 BHP.
			22.	Steam Inlet Diameter: 2 inches (50.8 mm).
			23.	Condensate Outlet Diameter: 1.5 inches (38.1 mm).
	** NOTE TO SPECIFIER ** Select Hot Oil Flow based on width. 225 gal/min for 118 inch, 255 gal/min for 130 inch and 269 gal/min for 138 inch, Delete two of the next three paragraphs. Delete next six paragraphs if Hot Oil Heater is not specified.
			24.	Hot Oil Flow - 225 gal/min (850 l/hr).
			25.	Hot Oil Flow - 255 gal/min (965 l/hr).
			26.	Hot Oil Flow - 269 gal/min (1020 l/hr).
			27.	Hot Oil Pressure: 29 psi (2 bar).
			28.	Hot Oil Inlet Diameter: 3 inches (76.2 mm).
			29.	Hot Oil Outlet Diameter: 3 inches (76.2 mm).
		D.	Model - 3 Roll- F32___DS:
			1.	Cylinder Diameter: 31.5 inches (800mm).
	** NOTE TO SPECIFIER ** Select Length. Delete two of the next three paragraphs.
			2.	Useable Cylinder Length: 118.1 inches (3000 mm).
			3.	Useable Cylinder Length: 129.9 inches (3300 mm).
			4.	Useable Cylinder Length: 137.8 inches (3500 mm).
			5.	Ironing Speed: 16 to 131 ft (5 to 40 m) per minute.
			6.	Exhaust Diameter: 9.8 inches (250 mm).
			7.	Exhaust Air Flow: 1907 cfm (3240 cu m/h).
			8.	Drive Motor: 29.5 HP.
			9.	Blower Motor: 3 x 1.74 HP.
			10.	Fan Motor: 0.24 HP.
			11.	Compressed Air Flow: 53 gal/min (200 l/hr).
			12.	Compressed Air Diameter: 0.5 inches (12.7 mm).
			13.	Size / Dimensions: Height: 65 inches (1650 mm).
			14.	Size / Dimensions: Depth: 190 inches (4848 mm).
	** NOTE TO SPECIFIER ** Select Size/Dimensions based on width.. 173 inches for 118", 185 inches for 130" and 193 inches for 138". Delete one of the next three paragraphs.
			15.	Size / Dimensions: Width: 173 inches (4400 mm).
			16.	Size / Dimensions: Width: 185 inches (4700 mm).
			17.	Size / Dimensions: Width: 193 inches (4900 mm).
	** NOTE TO SPECIFIER ** Select Full Load based on power. Delete one of the next two paragraphs
			18.	Full Load 208-240/Three Phase: 85.7A.
			19.	Full Load 440-480/Three Phase: 49.2A.
	** NOTE TO SPECIFIER ** Select Heater based on width. 1373620 BTU for 118 inch, 1508600 BTU for 130 inch and 1595940 BTU for 138 inch, Delete two of the next three paragraphs, Delete next five paragraphs if Steam Heater is not specified.
			20.	Heater: Steam - 1,373,620 BTU.
				a.	Consumption: 1191 lbs/h (540 kg/h).
				b.	Pressure: 116 psi (8 bar).
				c.	BHP Consumption: 32.8 BHP.
			21.	Heater: Steam - 1,508,600 BTU.
				a.	Consumption: 1323 lbs/h (600 kg/h).
				b.	Pressure: 116 psi (8 bar).
				c.	BHP Consumption: 36.1 BHP.
			22.	Heater: Steam - 1,595,940 BTU.
				a.	Consumption: 1389 lbs/h (630 kg/h).
				b.	Pressure: 116 psi (8 bar).
				c.	BHP Consumption: 38.2 BHP.
			23.	Steam Inlet Diameter: 2 inches (51 mm).
			24.	Condensate Outlet Diameter: 1.5 inches (38.1 mm).
	** NOTE TO SPECIFIER ** Select Hot Oil Flow based on width. 357 gal/min for 118 inch, 394 gal/min for 130 inch and 416 gal/min for 138 inch, Delete two of the next three paragraphs. Delete next six paragraphs if Hot Oil Heater is not specified.
			25.	Hot Oil Flow - 357 gal/min (1350 l/hr).
			26.	Hot Oil Flow - 394 gal/min (1490 l/hr).
			27.	Hot Oil Flow - 416 gal/min (1575 l/hr).
			28.	Hot Oil Pressure: 29 psi (2 bar).
			29.	Hot Oil Inlet Diameter: 3 inches (76.2 mm).
			30.	Hot Oil Outlet Diameter: 3 inches (76.2 mm).
	PART 3	EXECUTION
	3.1	EXAMINATION
		A.	Do not begin installation until substrates have been properly prepared.
		B.	If substrate preparation is the responsibility of another installer, notify Architect of unsatisfactory preparation before proceeding.
	3.2	PREPARATION
		A.	Clean surfaces thoroughly prior to installation.
		B.	Prepare surfaces using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions.
		C.	Check surfaces for level prior to installing equipment. If surfaces are not in an acceptable condition, notify the Architect immediately of the condition.
	3.3	INSTALLATION
		A.	Install in accordance with manufacturer's instructions.
		B.	Install all hookups in accordance with UPC and NEC requirements.
	3.4	PROTECTION
		A.	Protect installed products until completion of project.
		B.	Touch-up, repair or replace damaged products before Substantial Completion.
	END OF SECTION